MXenes-based materials are considered to be one of the most promising electrode materials in the field of sodium-ion batteries due to their excellent flexibility, high conductivity and tuneable surface functional groups. However, MXenes often have severe self-agglomeration, low capacity and unsatisfactory durability, which affects their practical value. The design and synthesis of advanced heterostructures with advanced chemical structures and excellent electrochemical performance for sodium-ion batteries have been widely studied and developed in the field of energy storage devices. In this review, the design and synthesis strategies of MXenes-based sodium-ion battery anode materials and the influence of various synthesis strategies on the structure and properties of MXenes-based materials are comprehensively summarized. Then, the first-principles research progress of MXenes-based sodium-ion battery anode materials is summarized, and the relationship between the storage mechanism and structure of sodium-ion batteries and the electrochemical performance is revealed. Finally, the key challenges and future research directions of the current design and synthesis strategies and first principles of these MXenes-based sodium-ion battery anode materials are introduced.
Sr2TiO4 is a promising photocatalyst for antibiotic degradation in wastewater. The photocatalytic performance of pristine Sr2TiO4 is limited to its wide bandgap, especially under visible light. Doping is an effective strategy to enhance photocatalytic performance. In this work, Nb/N co-doped layered perovskite Sr2TiO4 (Sr2TiO4:N,Nb) with varying percentages (0–5 at%) of Nb were synthesized by sol-gel and calcination. Nb/N co-doping slightly expanded the unit cell of Sr2TiO4. Their photocatalytic performance towards antibiotic (tetracycline) was studied under visible light (λ > 420 nm). When Nb/(Nb + Ti) was 2 at%, Sr2TiO4:N,Nb(2%) shows optimal photocatalytic performance with the 99% degradation after 60 min visible light irradiation, which is higher than pristine Sr2TiO4 (40%). The enhancement in photocatalytic performance is attributed to improving light absorption, and photo-generated charges separation derived from Nb/N co-doping. Sr2TiO4:N,Nb(2%) shows good stability after five cycles photocatalytic degradation reaction. The capture experiments confirm that superoxide radical is the leading active species during the photocatalytic degradation process. Therefore, the Nb/N co-doping in this work could be used as an efficient strategy for perovskite-type semiconductor to realize visible light driving for wastewater treatment.
30 December 2022 in Russian Journal of Physical Chemistry A
Flower-like SrTiO3 was prepared by hydrothermal method and BiVO4 was prepared by sol–gel method, and then the two materials were fully mixed under the condition of calcination at 500°C for 2 h. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and UV–Vis diffuse reflectance spectroscopy (DRS) and electrochemical impedance spectroscopy (EIS). The results showed that the BiVO4 nanoparticles were embedded on the flower-like SrTiO3, and the heterojunction between BiVO4 and SrTiO3 was formed which effectively improved the migration efficiency of photogenerated carriers. The UV–Vis test results indicated that the corresponding range of STO–10 wt % BVO composite photocatalyst changes from 380 to 490 nm, and the photocatalytic efficiency reached 72% by degrading tetracycline hydrochloride (TC) under simulated sunlight. Mechanism analysis shows that the type I heterojunction is successfully built between SrTiO3 and BiVO4, which promotes the migration and separation of photogenerated carriers and reduces the recombination rate of photogenerated electrons and holes.
1 January 2023 in Russian Journal of Physical Chemistry A
Graphite-like carbon nitride (g-C3N4) has attracted wide attention in the field of photocatalysis due to its simple and feasible preparation method and appropriate energy gap structure for light absorption in a wide range. However, its high recombination rate of photo-generated electrons and holes affects its catalytic efficiency. In this paper, type II strontium titanate/graphite-like carbon nitride (SrTiO3/g-C3N4) heterojunction photocatalysts were designed and prepared by mixed calcination method. The results of XRD and IR spectra have showed that the two semiconductors were well combined. The wider light absorption range was found in the 10 wt % SrTiO3 composite materials by UV–Vis diffuse reflection spectrum, and it was proved that the recombination of photo-generated electrons and holes was greatly reduced by PL spectrum and photoelectric tests. The photocatalytic degradation ratio of 10 wt %–SrTiO3/g-C3N4 composite materials was about 56 times higher than that of pure g-C3N4 by degrading tetracycline drugs (TCN), and the performance of photocatalytic degradation of TCN still remained at about 96.4% after five cycles. The photocatalytic mechanism analysis indicates that the type-II heterojunction photocatalysts are formed between SrTiO3 and g-C3N4 composite materials, and the reasons for improving photocatalytic degradation efficiency of TCN are explained.
Introducing second-phase materials to construct heterojunctions can effectively improve the photoelectrochemical performance of semiconductor materials. In this study, tungsten trioxide/strontium titanate (WO3/SrTiO3) composites are designed and prepared to protect 304 stainless steel (304 SS) via photochemical cathodic protection (PCP) technology in a simulated sunlight environment. The results demonstrate that the photoelectric properties of composites containing WO3 with different mass fractions and SrTiO3 vary, and the composites show enhanced PCP performance. Coupling 304 SS with the WO3/SrTiO3 composites containing 20 wt % of WO3 shifts the potential of the 304 SS from –0.13 to –0.34 V, and the composites generate 4.5 times more photocurrent density than SrTiO3 alone. Heterojunction electric fields formed on the interface of WO3/SrTiO3 enhance the separation efficiency of photogenerated electrons and holes, promoting PCP performance. An appropriate amount of WO3 loaded on the surface of SrTiO3 can provide effective protection for 304 SS under visible light. This is mainly because the special flower like structure on the surface of SrTiO3 has a large number of voids, which not only has a large surface area and provides more reaction sites, but also is conducive to the multiple reflection of incident light and improves the utilization of light. Moreover, heterojunction electric fields formed on the interface of WO3/SrTiO3 enhance the separation efficiency of photogenerated electrons and holes, promoting PCP performance.