Shan Gao

Dr. Shan Gao


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 February 2026 in Metals
Verified
Journal Article
Open access
PDF file
XJXu Jiang
Xu Jiang
SGShan Gao
Shan Gao
XZXintian Zhao
Xintian Zhao
Hongyu ZHENGHongyu ZHENG
Hongyu ZHENG
Yongling WuYongling Wu
Yongling Wu
ZONGSHEN WANGZONGSHEN WANG
ZONGSHEN WANG
With the growing demand for high-performance die materials under harsh service conditions, the development of composite coatings with enhanced hardness and wear resistance has attracted significant attention. In this study, homogeneous laser cladding was employed to fabricate H13 alloy coatings reinforced with varying TiC contents (0, 10, 20, and 30 in wt.%) on H13 steel, which minimizes compositional segregation and ensures strong metallurgical bonding. TiC particles acted as heterogeneous nucleation sites during solidification, refining the microstructure and enhancing phase stability. The coatings consisted of initial TiC residues, newly formed primary and eutectic TiC, as well as austenite and martensite phases. With increasing TiC addition, TiC morphology evolved from fine particles to complex fishbone-like and polygonal structures. The coating containing 30% TiC achieved the highest hardness of 1095.9 HV0.5, approximately five times that of the as-annealed H13 steel substrate while the 20% TiC coating exhibited optimal high-temperature wear resistance. Under the sliding conditions at 600 °C, the friction coefficient decreased from 0.467 for the substrate to 0.367 for the 20% TiC coating, accompanied by a remarkable reduction in wear rate from 27.45 × 10−4 mm3 N−1 m−1 to 4.32 × 10−4 mm3 N−1 m−1. The superior performance was attributed to the multiscale TiC reinforcement mechanism: initial TiC promoted grain refinement and strong interfacial bonding, in situ formed primary TiC induced lattice distortion and dislocation strengthening, and eutectic TiC reinforced grain boundaries, jointly enhancing hardness, thermal stability, and wear resistance.

15 December 2025 in Metals
Verified
Journal Article
Open access
PDF file
SGShan Gao
Shan Gao
WWWenquan Wang
Wenquan Wang
XZXintian Zhao
Xintian Zhao
WYWenhui Yu
Wenhui Yu
Hongyu ZHENGHongyu ZHENG
Hongyu ZHENG
ZONGSHEN WANGZONGSHEN WANG
ZONGSHEN WANG
Mg alloys show great potential in biomedical fields due to superior biocompatibility and biodegradability. Additive manufacturing (AM) provides opportunities in fabricating metallic implants with complex geometries while inherent defects during AM limit its further applications. In this work, laser shock peening (LSP) was employed as a post-processing technique to tailor the surface integrity and corrosion resistance of additively manufactured AZ91 Mg alloy by selective laser melting (SLM). The surface morphology, microstructure and porosity, surface hardness and residual stress, and corrosion resistance of the SLMed alloy before and after LSP were examined. The results show that a gradient structure is formed along the depth direction after LSP and high-density dislocations and high-fraction low-angle grain boundaries are induced. The porosity is gradually reduced in number and size and the highest density of 1.794 g/cm3 is obtained after two impacts of LSP. The surface hardness and residual compressive stress both increase with LSP number and the highest values of 135.26 HV and 40.13 MPa after four impacts, respectively. All of the SLMed alloy samples show improved corrosion resistance after LSP. This work provides a promising route for enhancing the performance of additively manufactured Mg alloys through laser materials surface modification.

12 February 2026 in Metals
Verified
Journal Article
Open access
PDF file
SGShan Gao
Shan Gao
HSHaolei Song
Haolei Song
TZTong Zang
Tong Zang
Hongyu ZHENGHongyu ZHENG
Hongyu ZHENG
Harry M NgwangwaHarry M Ngwangwa
Harry M Ngwangwa
ZONGSHEN WANGZONGSHEN WANG
ZONGSHEN WANG
The present study investigates the impact of femtosecond laser shock peening (FLSP) on the corrosion resistance of an AZ31 magnesium alloy. The alloy was subjected to irradiation with varying pulse energies in an air environment, and subsequent modifications in surface properties were characterized. Surface wettability, assessed by contact angle measurements, indicated enhanced hydrophobicity following FLSP, especially at higher pulse energies. Corrosion behavior after immersion with various durations was assessed in a 3.5% NaCl solution using electrochemical polarization curves and electrochemical impedance spectroscopy, applying a three-electrode system. The results revealed that FLSP significantly augmented corrosion resistance; the most notable effects were observed at higher pulse energies. SEM/EDS analysis post-corrosion revealed a transition from localized to more uniform corrosion, accompanied by reduced pit size and density. XRD and XPS confirmed the formation of a protective Mg(OH)2 layer, which exhibited greater stability and uniformity at higher laser energies. The study concluded that FLSP represented an effective approach for enhancing the corrosion resistance of the AZ31 magnesium alloy, with potential applications in improving the longevity of magnesium alloy components in industrial settings.

2 April 2026 in Materials
Verified
Journal Article
Open access
PDF file
JHJunyi He
Junyi He
JLJie Liu
Jie Liu
XCXiaoli Cui
Xiaoli Cui
BLBinbin Li
Binbin Li
XTXiaoqing Tian
Xiaoqing Tian
DTDi Tie
Di Tie
Aluminum–silicon (Al-Si) alloys are widely used in aerospace, automotive manufacturing, power electronics, marine engineering and other fields due to their excellent physical properties. However, their corrosion resistance is insufficient in harsh service environments. In this study, a variety of characterization methods were adopted, including scanning electron microscopy (SEM), X-ray diffraction (XRD), electrochemical measurements (electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization), immersion corrosion tests, and scanning vibrating electrode technique (SVET). The results show that the appropriate heat treatment regime can significantly enhance the corrosion resistance of the alloy, while improper aging parameters will aggravate the corrosion tendency. The optimal heat treatment regime is solution treatment at 500 °C for 4 h followed by aging at 200 °C for 48 h. Under this condition, the corrosion current density (icorr) is as low as 79.30 μA/cm2, and the low-frequency impedance modulus and phase angle in EIS tests are optimal. The as-extruded alloy exhibits severe localized corrosion, while the heat-treated alloy transforms into mild and uniform corrosion. The underlying mechanism is that heat treatment induces the formation of uniformly distributed nanoscale Mg2Si and Al3(Sc,Zr) precipitates, which synergistically improve the corrosion resistance of the alloy by weakening micro-galvanic coupling and facilitating the formation of a stable passive film.