ZONGSHEN WANG

Prof. Dr. ZONGSHEN WANG

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2017 in Composite Structures
Verified
Journal Article
Closed access
YAYukun An
Yukun An
SYSiyi Yang
Siyi Yang
EZErtuan Zhao
Ertuan Zhao
ZONGSHEN WANGZONGSHEN WANG
ZONGSHEN WANG

22 March 2019 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
ZONGSHEN WANGZONGSHEN WANG
ZONGSHEN WANG
TWTao Wang
Tao Wang
YGYanjin Guan
Yanjin Guan
XWXiuting Wei
Xiuting Wei
XFXiaoying Fang
Xiaoying Fang
SGShan Gao
Shan Gao

27 October 2020 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
LZLihua Zhu
Lihua Zhu
YGYanjin Guan
Yanjin Guan
ZONGSHEN WANGZONGSHEN WANG
ZONGSHEN WANG
HZHongyu Zheng
Hongyu Zheng
JLJun Lin
Jun Lin
ZXZhendong Xie
Zhendong Xie

26 September 2019 in Metals
Verified
Journal Article
Open access
PDF file
ZONGSHEN WANGZONGSHEN WANG
ZONGSHEN WANG
YGYanjin Guan
Yanjin Guan
LLLin Li
Lin Li
LZLihua Zhu
Lihua Zhu
Constrained groove pressing (CGP) is one of the most promising severe plastic deformation (SPD) techniques suitable for producing ultra-fine grained (UFG) sheet or plane metallic materials with unique physical, chemical, and mechanical properties. However, the heavily deformed sheets are usually with high strength but low ductility due to work hardening and micro-cracking, and the UFG microstructure and high strength are unstable especially when exposed to high temperatures. Thus, in this work, CGP was conducted on commercially pure nickel sheets and, firstly, the fracture mechanism of the processed sheets was examined. Then, the annealing behavior of CGP nickel sheets was investigated in detail to explore their thermal stability and improve their ductility. The results showed that significant grain refinement and strength improvement of the nickel sheets were achieved with great loss of ductility. The fracture surface morphology of the sheet sample exhibited typical characteristics of fatigue fracture, and inhomogeneous strain distribution and work hardening determined the micro-crack initiation position and propagation direction. The CGP sheets by one and two passes showed high thermal stability up to 650 and 600 °C, respectively, owing to different stored internal stresses and accumulated energy. In both cases, obvious recovery of elongation to failure from 12.7% and 10.6% to 29.3% and 27.3% were achieved by CGP with post-deformation annealing treatment, respectively, with acceptable drop of strength.

26 February 2026 in Metals
Verified
Journal Article
Open access
PDF file
XJXu Jiang
Xu Jiang
SGShan Gao
Shan Gao
XZXintian Zhao
Xintian Zhao
Hongyu ZHENGHongyu ZHENG
Hongyu ZHENG
Yongling WuYongling Wu
Yongling Wu
ZONGSHEN WANGZONGSHEN WANG
ZONGSHEN WANG
With the growing demand for high-performance die materials under harsh service conditions, the development of composite coatings with enhanced hardness and wear resistance has attracted significant attention. In this study, homogeneous laser cladding was employed to fabricate H13 alloy coatings reinforced with varying TiC contents (0, 10, 20, and 30 in wt.%) on H13 steel, which minimizes compositional segregation and ensures strong metallurgical bonding. TiC particles acted as heterogeneous nucleation sites during solidification, refining the microstructure and enhancing phase stability. The coatings consisted of initial TiC residues, newly formed primary and eutectic TiC, as well as austenite and martensite phases. With increasing TiC addition, TiC morphology evolved from fine particles to complex fishbone-like and polygonal structures. The coating containing 30% TiC achieved the highest hardness of 1095.9 HV0.5, approximately five times that of the as-annealed H13 steel substrate while the 20% TiC coating exhibited optimal high-temperature wear resistance. Under the sliding conditions at 600 °C, the friction coefficient decreased from 0.467 for the substrate to 0.367 for the 20% TiC coating, accompanied by a remarkable reduction in wear rate from 27.45 × 10−4 mm3 N−1 m−1 to 4.32 × 10−4 mm3 N−1 m−1. The superior performance was attributed to the multiscale TiC reinforcement mechanism: initial TiC promoted grain refinement and strong interfacial bonding, in situ formed primary TiC induced lattice distortion and dislocation strengthening, and eutectic TiC reinforced grain boundaries, jointly enhancing hardness, thermal stability, and wear resistance.

22 August 2020 in Advanced Engineering Materials
Verified
Journal Article
Closed access
PDF file
ZONGSHEN WANGZONGSHEN WANG
ZONGSHEN WANG
BZBin Zhang
Bin Zhang
Wei ZhouWei Zhou
Wei Zhou
LZLihua Zhu
Lihua Zhu
HZHongyu Zheng
Hongyu Zheng
WZWengang Zhai
Wengang Zhai