PID (proportional integral derivative) control has been widely used in industry due to its simplicity in implementation and satisfactory performance. However, the controller tuning is very troublesome when used in complex and nonlinear systems. The full bridge boost converter (FBBC) is a nonlinear system, so the PID control application in this converter should be further explored. This paper introduces a control approach that integrates PID control with a Linear Quadratic Regulator (LQR) for FBBC. To enable linear control design, the FBBC is linearized around its steady state operating points. The control architecture is structured into four cases: Case 1: PI-LQR Output Feedback, Case 2: PI-LQR State Feedback, Case 3: PID-LQR Output Feedback, and Case 4: PID-LQR State Feedback. The analysis aims to identify the most reliable system performance under input voltage change and load variation. The simulation results indicate that under the input voltage and load changes, cases 2 and 4 produce faster settling times, each with a settling time of 0.025 s and 0.015 s, respectively. However, both controllers produce negligible steady state error (less than 1%). Overall, Case 4 (PID-LQR State Feedback) consistently delivers the best performance, characterized by faster settling time, negligible steady state error, optimal control signal, and significantly reduced oscillation in both the inductor current and output voltage.
Reliable steering regulation under varying road curvature and actuator constraints remains a central challenge in autonomous electric vehicles (AEVs). Many exiting approaches rely on reactive error correction or treat preview information solely as a reference adjustment, limiting anticipation and physical consistency. This study proposes a prediction–preview steering control (PSC) framework in which future curvature information within state propagation and constraint handling enables forward-looking steering decisions while respecting dynamic and actuator limits. The method is evaluated using a lateral-heading vehicle model with real-road geometric variation. Experimental results indicate significant improvement in tracking performance, reducing lateral RMSE from 0.1747 m to 0.0074 m with a maximum deviation of 0.0889 m and limiting heading RMSE to 0.0867° (maximum 1.2046°). Steering angle commands remain bounded within ±8.7°, while steering angle rate is maintained within 40–60°/s, ensuring smooth and dynamically admissible operation. The proposed strategy offers a computationally efficient solution for embedded AEV steering systems and demonstrates improved robustness under practical curvature transitions.
Signal conditioning is needed in inverter current and voltage measurements to conform the ADC (analog to digital converter) level of microcontroller or FPGA (fi Signal conditioning is needed in inverter current and voltage measurements to conform the ADC (analog to digital converter) level of microcontroller or FPGA (fi
Optimal path tracking is a fundamental requirement for autonomous electric vehicles to ensure safety, stability, and driving comfort. This paper introduces a Prediction–Preview Cooperative Steering Control (MPC–PEM) method, which is a prediction-based steering control strategy designed to minimize lateral and heading errors. The approach utilizes a technique referred to as Preview Error Minimization (PEM). The controller predicts vehicle dynamics within a limited preview horizon to generate anticipative steering actions that adapt to road curvature and speed variations. A bicycle model is employed to represent the lateral–yaw dynamics, while the control law is formulated by considering system constraints and stability margins. Simulation results demonstrate that the proposed prediction–preview approach significantly improves tracking accuracy compared to conventional LQR and MPC methods, as evidenced by smaller heading and lateral errors, smoother steering angles, and more stable and realistic dynamic responses. This method offers an efficient, adaptive, and reliable steering control solution for the next generation of autonomous electric vehicles.
The paper introduces a novel control approach that integrates Proportional-Integral-Derivative (PID) control with a Linear Quadratic Regulator (LQR) for a Full-Bridge Boost Converter (FBBC). To enable effective linear control design, the FBBC system is linearized around its steady-state operating. The control architecture is structured into four cases: Case 1: PI-LQR Output Feedback, Case 2: PI-LQR State Feedback, Case 3: PID-LQR Output Feedback, and Case 4: PID-LQR State Feedback. Each case is evaluated for system responsiveness by examining output voltage stability, inductor current dynamics, and control signal characteristics. The analysis aims to identify the optimal and most reliable system performance under input voltage disturbance and load variation. The simulation results indicate that Case 3 (PID-LQR Output Feedback) consistently delivers the best performance, characterized by the shortest settling time, optimal control signal, and fast response to disturbances.