Inkjet printing technique allows manufacturing low cost organic light emitting diodes (OLEDs) in ambient conditions. The above approach enables upscaling of the OLEDs fabrication process which, as a result, would become faster than conventionally used vacuum based processing techniques. In this work, we use the inkjet printing technique to investigate the formation of thin active layers of well-known light emitting polymer material: Super Yellow (poly(para-phenylene vinylene) copolymer). We develop the formulation of Super Yellow ink, containing non-chlorinated solvents and allowing stable jetting. Optimization of ink composition and printing resolution were performed, until good quality films suitable for OLEDs were obtained. Fabricated OLEDs have shown a remarkable characteristics of performance, similar to the OLEDs fabricated by means of spin coating technique. We checked that, the values of mobility of the charge carriers in the printed films, measured by transient electroluminescence, are similar to the values of mobility measured in spin coated films. Our contribution provides a complete framework for inkjet printing of high quality Super Yellow films for OLEDs. The description of this method can be used to obtain efficient printed OLEDs both in academic and in industrial settings.
In this review article we cover the progress towards slot-die coated organic light emitting diodes (OLEDs). We showcase how emitting layers, charge transport layers, and electrodes can be slot-die coated to deliver practical OLED devices.
This study presents the slot-die coating process of two layers of organic materials for the fabrication of organic light emitting diodes (OLEDs). Poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS), which is commonly used in OLEDs and in organic photovoltaic devices as the hole injection layer (HIL), has been deposited via slot-die coating. Uniform films of PEDOT:PSS were obtained after optimizing the slot-die processing parameters: substrate temperature, coating speed, and ink flow rate. The film quality was examined using optical microscopy, profilometry, and atomic force microscopy. Further, poly(9,9-dioctylfluorene) (F8) and poly(9,9-dioctylfluorene-alt-benzothiadiazole) (F8BT), a well know polymer blend F8:F8BT, which is used as an emissive layer in OLEDs, has been slot-die coated. The optoelectronic properties of the slot-die coated F8:F8BT films were examined by means of photoluminescence (PL) and electroluminescence (EL) studies. The fabricated OLEDs, consisting of slot-die coated PEDOT:PSS and F8:F8BT films, were characterized to record the brightness and current efficiency.
28 August 2023 in IEEE Transactions on Electron Devices
In this article, we report on the fabrication of $\beta $ -Ga2O3 pseudo-CMOS inverters using enhancement-mode (E-mode) $\beta $ -Ga2O3 single-finger ( $\text{S}_{\text {F}}{)}$ and multifinger ( $\text{M}_{\text {F}}{)}$ thin-film transistors (TFTs). Initially, single-stage monolithic inverter ICs were fabricated using TFTs having threshold voltages ${V}_{\text {th}}^{\text {SF}}$ = 0.6 V and ${V}_{\text {th}}^{\text {MF}}$ = 0.1 V. However, the single-stage inverter yielded poorer gain (4.50 at ${V}_{\text {DD}}$ , supply voltage = 3 V). Alternatively, a pseudo-CMOS (double-stage) inverter was designed and fabricated, yielding a maximum gain of 6.45 but with a poor noise margin (NM). To improve the NM, the pseudo-CMOS circuit was tested using TFTs having higher threshold voltages ( ${V}_{\text {th}}^{\text {SF}}$ = 1.85 V and ${V}_{\text {th}}^{\text {MF}}$ = 1.75 V). Notably, the optimized pseudo-CMOS circuit exhibited the least peak power consumption (0.2 nW) and the maximum gain of 8 at ${V}_{\text {DD}}$ = 3 V. The monolithically integrated devices’ performance and IC highlight this technology’s remarkable potential for application in the emerging sector of power electronics and extreme-environment electronics.
The N-annulation of a benzothioxanthene imide (BTI) derivative is demonstrated herein affording the unprecedented thiochromenocarbazole imide (TCI). The impact of this chemical modification on the molecular structure and optoelectronic properties is investigated using a combination of single crystal X-ray diffraction, optical absorption spectroscopy, photoluminescence spectroscopy, cyclic voltammetry, and theoretical calculations. Comparison with the parent compound highlights the great potential of the newly synthesized molecule for applications in electroluminescent devices. As a proof of concept and seminal use, TCI-based dimers were successfully prepared and embedded in solution-processed organic light emitting devices (OLEDs). With improved solubility in non-halogenated solvents and good film forming capabilities, large active area (160 mm2) OLEDs, fabricated in ambient air on flexible substrates via slot-die-coating, were demonstrated.