Gas sensing performance characterization systems are essential for the research and development of gas sensing materials and devices. Although existing systems are almost completely automatically operated, the accuracies of gas concentration control and of pressure control and the ability to simultaneously detect different sensor signals still require improvement. In this study, a high-precision gas sensing material characterization system is developed based on vacuum technology, with the objective of enabling the precise and simultaneous measurement of electrical responses. Because of the implementation of vacuum technology, the gas concentration control accuracy is improved more than 1600 times, whereas the pressure of the test ambient condition can be precisely adjusted between vacuum and 1.2 bar. The vacuum-assisted gas-exchanging mechanism also enables the sensor response time to be determined more accurately. The system is capable of performing sensitivity, selectivity, and stability tests and can control the ambient relative humidity in a precise manner. More importantly, the levels of performance of three different optical signal measurement set-ups were investigated and compared in terms of detection range, linearity, noise, and response time, based on which of their scopes of application were proposed. Finally, single-period and cyclical tests were performed to examine the ability of the system to detect optical and electrical responses simultaneously, both at a single wavelength and in a spectral region.

In this study, a multifunctional high-vacuum system was established to measure the electro-optical conversion efficiency of metamaterial-based thermal emitters with built-in heaters. The system is composed of an environmental control module, an electro-optical conversion measurement module, and a system control module. The system can provide air, argon, high vacuum, and other conventional testing environments, combined with humidity control. The test chamber and sample holder are carefully designed to minimize heat transfer through thermal conduction and convection. The optical power measurements are realized using the combination of a water-cooled KBr flange, an integrating sphere, and thermopile detectors. This structure is very stable and can detect light emission at the μW level. The system can synchronously detect the heating voltage, heating current, optical power, sample temperatures (both top and bottom), ambient pressure, humidity, and other environmental parameters. The comprehensive parameter detection capability enables the system to monitor subtle sample changes and perform failure mechanism analysis with the aid of offline material analysis using scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction. Furthermore, the system can be used for fatigue and high-low temperature impact tests.

Polarization is an important concept in physics, and physics teachers have developed many experiments using the principle of polarization.1–4 We discovered an i

We present a novel approach for actively controlling electromagnetically induced transparency (EIT) analogs in a single-mode microstrip cavity. This cavity is side-coupled with a pair of varactor-loaded split-ring resonators (SRRs). The EIT-like effect is achieved through resonance hybridization between the paired SRRs with frequency detuning. The microstrip cavity is utilized to enhance the EIT-like transmission properties, including Q-factor and group delay. Varactor diodes, soldered at the gap of the SRRs, are biased electrically through a DC voltage source. This dynamic modulation setup allows for the tuning of the enhanced EIT analog. Experimental results demonstrate that the enhanced EIT-like transmission spectrum can be tuned reversibly by 378 MHz with respect to the transmission dip frequency of 2.464 GHz under the bias voltage ranging from 0 to 5 V. Simultaneously, the controlled transmission spectrum enables a remarkable change in group delay of 10.9 ns. Moreover, the modulation amplitude of the composite SRRs-cavity structure reaches a peak value of up to 34.5 dB, significantly higher than the 6.4 dB of the individual SRRs pair. These results hold promise for inspiring innovation in actively controlled photonic devices for practical applications.

Do people underwater looking at something out of the water have a wider visual field than if they were out of the water or if they were looking at something els Do people underwater looking at something out of the water have a wider visual field than if they were out of the water or if they were looking at something els

In this paper, we propose a microstrip Fabry–Pérot (FP) cavity embedded with an active electromagnetically-induced-transparency-like (EIT-like) meta-molecule to investigate the electrically switchable behavior. The phenomenon of EIT is achieved by coupling a ‘bright’ comb-line resonator with a ‘dark’ split-ring resonator. The FP cavity is fabricated by etching two narrow slots on a microstrip line. With two different resonance mechanisms working together, the proposed composite EIT-cavity design is shown to exhibit the enhanced EIT-like transmission characteristics, accompanied by two sharp Fano-type line-shapes. By incorporating PIN diodes into the composite EIT-cavity structure, we can dramatically modulate the transmission spectrum via external DC voltage. In particular, we show the multi-band unity modulations through biasing the proposed active samples. Moreover, the slow light on-to-off switching processes are also obtained with modifying the state of PIN diode from dielectric to conductive. Our results may open important opportunities for fabricating dynamic functional photonic devices in the future.