Purpose. Determination of the thermal effect (combustion) on the geochemical characteristics of waste rock argillite, and on the leachability of pollutants for establishing the potential of these compounds as a source of drainage and groundwater pollution. Methodology. The article describes the investigation of argillite, the main component of the basin’s waste heaps, the analysis of pollutant leaching from unburned and burned argillite using a washing plant, their X-ray fluorescence analysis, the surface morphology of different types of argillite by scanning electron microscopy (SEM), the qualitative and quantitative composition of samples using energy dispersive X-ray spectroscopy (EDS) and the content of water-soluble heavy metals by atomic absorption. Findings. As a result of thermal effects on argillite, the salt content in the washing water increases by 2.5 times and reaches 185 ppm in water from unburned rock and 462 ppm from burned rock, the sulfur content in the burned rock after washing decreased by 21.3 times. The variability of changes in the content of water-soluble compounds in the studied samples is also noted, since the amount of Mn, Pb, Cu and Co leached out is up to 15.5 times higher in unburned argillite, but the amount of Fe and Zn leached out after combustion increases up to 17.4 times compared to unburned rock. Originality. The series of changes in the content of chemical elements and compounds as a result of combustion and rock washing have been established, which are important for assessing and predicting the migration potential of chemical elements from coal dump rocks to soils and waters within coal spoil tips. Practical value. The conducted research characterises the ecological state of spoil tips and can be used for reclamation or melioration works in these areas, taking into account the degree of rock metamorphism.
The crystal structure of La2Mg17-xSnx solid solution was determined by single crystal X-ray diffraction for the first time. This phase crystallizes in hexagonal symmetry with space group P63/mmc (a = 10.3911(3), c = 10.2702(3) Å, V = 960.36(6) Å3, R1 = 0.0180, wR2 = 0.0443 for the composition La3.65Mg30Sn1.10) and is related to the structure of CeMg10.3 and Th2Ni17-types which are derivative from the CaCu5-type. A series of isotypical solid solutions La2Mg17-xMx (M = Ni, Sn, Sb, x ~0.8) was synthesized and studied by X-ray powder diffraction, energy dispersive X-ray spectroscopy and fluorescent X-ray spectroscopy. All solid solutions crystallize with the structure related to the Th2Ni17-type. The electrochemical hydrogenation confirmed the similar electrochemical behavior of all studied alloys. The amount of deintercalated hydrogen depends on the physical and chemical characteristics of doping elements and increases in the sequence Sn < Mg < Sb < Ni. The most geometrically advantageous sites are octahedral voids 6h of the initial structure, thus a coordination polyhedron for H-atom is an octahedron [HLa2(Mg,M)4].
It was established that the change in the structure of the amorphous metal alloy (AMA) as a result of heat treatment of the amorphous metal alloy Al87Gd5Ni4Fe4 at T=645 ±1 K significantly affects the decolorization of the dye Basic Blue 6/Mendola Blue (BB6/MB) at pH=1.7±0.3. The MB solution...
18 December 2022 in Physics and Chemistry of Solid State
New Li-containing solid solutions LiyM1-xCaxMnO3 (M = Pr and Eu) were synthesized by electrochemical lithiation of the ceramics with perovskite structure. The qualitative and quantitative composition of the initial and Li-containing ceramics was determined by scanning electron microscopy and energy-dispersive X-ray spectroscopy. The M/Ca/Mn cation ratio was confirmed by X-ray fluorescence spectroscopy. The crystal structure of theM1-xCaxMnO3solid solutions before lithiation (GdFeO3-type structure, space group Pnma, Pearson code oP20) and after lithiation (filled-up GdFeO3-type) was determined by the Rietveld method. X-ray structural analysis showed the formation of phases with increased unit cell parameters after lithiation process. In the case of Eu and Pr-containing samples X-rays diffraction patterns illustrate the amorphous halo based on the by-products of reaction between of ceramics surface and components from electrolyte. Under experimental conditions (Li-metal anode) the quantity of intercalated Li increases for ceramics: Li0.084Eu0.5Ca0.5MnO3, Li0.113Pr0.5Ca0.5MnO3, and Li0.134Pr0.7Ca0.3MnO3. Scanning electron microscopy method revealed the formation of Li-containing aggregates with dimension of 200-900 nm. The grains demonstrate block-like or irregular shape morphology with developed area surface.