This research aims to establish design guidelines for a cantilever triple-layer piezoelectric harvester (CTLPH) with tip mass and tip excitation, operating under resonance conditions. The guideline is derived by combining constitutive equations with Euler–Bernoulli beam theory to identify the effective parameters of the CTLPH and, subsequently, the storage voltage after rectification using a germanium diode bridge. The analysis shows that excitation frequency, piezoelectric coefficients, geometrical dimensions, and the mechanical properties of the layers all significantly influence CTLPH performance. The effects of storage capacitance and excitation frequency were experimentally validated through the design, fabrication, and testing of a prototype. Furthermore, the LTC3588 energy storage module was employed to store the generated charge from resonance motion. An advanced non-contact optical method was employed to determine the bending stiffness of the CTLPH. The output power after the energy storage module was measured across a range of resistive loads at frequencies near the resonance condition (f = 65 Hz). Results demonstrate that both excitation frequency and external resistance affect the maximum harvested power. The developed CTLPH achieved an optimum output power of 46.18 ± 0.98 μW at an external resistance of 3 kΩ, which is sufficient to supply micropower sensors.
Oman is strategically enhancing its renewable energy landscape, particularly through solar and wind energy initiatives. While these efforts contribute significantly to reducing greenhouse gas emissions and diversifying the energy mix, they also induce challenges related to fluctuations in electricity generation. This paper focuses on two types of fluctuations affecting the electricity grid: the slow, manageable changes and the rapid, unpredictable shifts primarily caused by solar energy generation disruptions, such as transient shadows. We conduct an in-depth analysis of renewable energy farms in Oman, assessing their impacts and the challenges they present. Furthermore, we explore innovative solutions to mitigate these rapid fluctuations, specifically through the use of advanced energy storage systems, including hydrogen storage and generators, as well as gravitricity and loop water dams. By proposing an Integrated Model and a Framework for Integration, this study underscores the potential of these technologies to stabilize the grid while enhancing energy reliability and sustainability. Ultimately, our findings provide actionable insights for policymakers, energy developers, and researchers seeking effective strategies for a resilient, low-carbon energy future.
This paper aims to enhance Smith-predictor-based control systems (SPCSs) for multi-input multi-output (MIMO) time delay processes. Conventional SPCSs for MIMO processes are composed of an array of classical feedback controller(s). These controllers act on error signals, calculated through deducting a predicted output by a Smith predictor from a reference signal at the time of operation. Investigations on underperformance of conventional SPCSs identified two major shortcomings: (i) the design of classical feedback controllers is based on trade-off, and their use may lead to windup phenomenon, this adversely influences conventional SPCSs performance, (ii) a predicted output by a Smith predictor belongs to a time in the future and does not concurrent with the reference at the time of operation; that is, in conventional SPCSs, the control error is generated using two asynchronous signals. This paper proposes an enhanced SPCS design method for MIMO time-delay systems based on two enhancements to tackle the aforementioned dual shortcomings. The proposed control system evidently outperforms a conventional SPCS with proportional-integral-derivative (PID) feedback controllers. The case study is a catalytic stirred tank reactor (CSTR) with three inputs (feed and water flow rates and auxiliary temperature), two outputs (output flow concentration and temperature) and three time delays. The presented model of the CSTR is more comprehensive than any CSTR model found in the literature.
This paper introduces an enhanced Smith-predictor-based control system (SPCS) for multi-input multi-output (MIMO) time delay processes. A conventional SPCS for an MIMO process is composed of a Smith predictor matrix providing predicted outputs and an array of classical feedback controllers. These controllers act on predicted error signals, calculated by subtracting the predicted output from the reference signal at the time of operation. Two major shortcomings were idented for the underperformance of conventional SPCSs for MIMO time-delay processes: (i) the employed classical feedback controllers are designed based on trade-off. Moreover, their use may lead to a windup phenomenon, which adversely influences the control performance of conventional SPCSs; (ii) a predicted output generated by a Smith predictor corresponds to a future time and is therefore not concurrent with the reference at the time of operation. Thus, in conventional SPCSs, the control error is generated using two asynchronous signals. This article proposes two enhancements to tackle the aforementioned dual shortcomings in SPCSs for MIMO time-delay systems. The proposed control system is shown to distinctly outperform a conventional SPCS with proportional-integral-derivative (PID) feedback controllers. The case study is a catalytic stirred tank reactor (CSTR) with three inputs (feed and water flow rates and auxiliary temperature), two outputs (output flow concentration and temperature) and three different time delays. The presented CSTR model, used for the design and simulations, is more comprehensive than any CSTR model reported in the literature.