Particularly in the automotive industry, the combination of dissimilar materials presents manufacturing engineering with major challenges. Notably, the adapted use of plastic and metal opens up further potential for weight savings. Directly and firmly bonding the two materials together fails, however, on account of the chemical and physical dissimilarity of plastic and metal. Since joining of plastics and metals nowadays is based on adhesive bonding, the joint is weak and underlies ageing processes. A promising approach to overcome these problems is a laser based two-step process. In the first process step laser radiation is applied to generate microstructures on the surface of the metallic joining partner. In the subsequent laser joining process, the plastic is molten and interlocked into the microstructures after curing. The mechanical strength of the joint depends strongly on the load direction and can be influenced by the geometry and arrangement of microstructures. These influencing factors are investigated for three different load directions (tensile shear, tensile and peel) by experiments and by structural mechanics simulations

Laser welding of copper is being used with increasing demand for contacting applications in electric components such as batteries, power electronics, and electric drives. With its local, non-contact energy input and high automation capability enabling reproducible weld quality, this joining technology represents a key enabler of future mobility systems. However, a major challenge in process design is the combination of energy efficiency and precise process guidance in terms of weld seam depth and defect prevention (i.e., spatter and melt ejections) due to the high electrical and thermal conductivity of copper. High-power lasers in the near infrared wavelength range (𝜆 ≈ 1 μm) and excellent beam quality provide an established joining solution for this purpose; nevertheless, the low absorptivity (≤5%) advocates novel beam sources at visible wavelengths due to altered absorptivity (40% at 515 nm) characteristics as an improved tool. In order to understand the influence of laser wavelength and process parameters on the vapor capillary geometry, in situ synchrotron investigations on Cu-ETP with 515 nm and 1030 nm laser sources with the same spot diameter are compared. The material phase contrast analysis was successfully used to distinguish keyhole and melt pool phase boundaries during the welding process. A significantly different sensitivity of the keyhole depth in relation to the feed rate was found, which is increased for the infrared laser. This behavior could be attributed to the increased effect of multiple reflections at 1030 nm.

The growing electrification of vehicles and tools increases the demand for low resistance contacts. Today’s batteries for electric vehicles consist of large quantities of single battery cells to reach the desired nominal voltage and energy. Each single cell needs a contacting of its cell terminals, which raises the necessity of an automated contacting process with low joint resistances to reduce the energy loss in the cell transitions. A capable joining process suitable for highly electrically conductive materials like copper or aluminium is the laser beam welding. This study contains the theoretical examination of the joint resistance and a simulation of the current flow dependent on the contacting welds’ position in an overlap configuration. The results are verified by examinations of laser-welded joints in a test bench environment. The investigations are analysing the influence of the shape and position of the weld seams as well as the influence of the laser welding parameters. The investigation identifies a tendency for current to flow predominantly through a contact’s edges. The use of a double weld seam with the largest possible distance greatly increases the joint’s conductivity, by leveraging this tendency and implementing a parallel connection. A simplistic increase of welded contact area does not only have a significantly smaller effect on the overall conductivity, but can eventually also reduce it.

To join plastic to metal a laser based two-step laser process is described. The first process step is the laser micro structuring of the metal surface to create microstructures with undercut grooves. The subsequent transmission joining process allows a selective heating of arbitrary component geometries and the local control of the joining temperature. Both parts are brought into direct contact prior to welding. The plastic part is melted and expands into the microstructures through the external clamping pressure. The joining results due to micro cramping after setting. The long term stability of the joining is described

Full-penetration laser beam welding is characterized by a weld seam whose depth equals the material thickness. It is associated with a stable capillary and is therefore widely used for welding of sheet metal components. The realization of lightweight concepts in car body production requires the application of high-strength aluminum alloys that contain magnesium as an alloying element, which significantly influences the evaporation temperature and pressure. This change of the evaporation processes influences the geometry of the capillary and therefore its absorptance. In order to quantify the influence of magnesium on the capillary, their geometries were captured by means of high-speed synchrotron X-ray imaging during the welding process of the aluminum alloys AA1050A (Al99.5), AA5754 (AlMg3) and AA6016 (AlSi1.2Mg0.4). The 3D-geometries of the capillaries were reconstructed from the intensity distribution in the recorded X-ray images and their absorptance of the incident laser beam was determined by the analysis of the reconstructed 3D-geometry with a raytracing algorithm. The results presented in this paper capture for the first time the influence of the magnesium content in high-strength aluminum alloys on the aspect ratio of the capillary, which explains the reduced absorptance in case of full-penetration laser beam welding of aluminum alloys with a high content of volatile elements. In order to improve the absorptance in full-penetration welding, these findings provide the information required for the deduction of new optimization approaches.

Unlike other joining techniques, laser transmission welding offers unique advantages such as selective and contactless energy deposition. This enables the fabrication of flexible seam geometries at low mechanical and thermal stresses. However, the use of absorbing additives for the lower joining partner such as carbon black is crucial as most polymers are transparent in the spectral range of typical beam sources (800–1100 nm). A novel approach is the application of beam sources emitting radiation within the polymeric intrinsic absorption bands between 1500 and 2000 nm. This enables absorber-free laser welding of transparent polymers for medical or microfluidic applications such as Lab-on-a-Chip devices. The main drawback on the other hand is the large heat affected zone (HAZ) due to the volume absorption which is extending over the entire cross section. A possible way to overcome this disadvantage is a quasi-simultaneous irradiation strategy. It could be proved in the past that the HAZ of polycarbonate (PC) can be reduced in the vertical direction by up to 30% compared with contour welding. Since the effects of light scattering on the absorber-free quasi-simultaneous irradiation strategy are still unknown, the beam propagation was simulated in polypropylene (PP). Based on the results, a thermal simulation of the welding process was carried out using the finite element method (FEM). The simulation model was then evaluated by comparing the results with experimental trials.