Serhan İLKENTAPAR

Dr. Serhan İLKENTAPAR

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2015 in KSCE Journal of Civil Engineering
Verified
Journal Article
Open access
PDF file
CBCahit Bilim
Cahit Bilim
OKOkan Karahan
Okan Karahan
CACengiz Duran Atiş
Cengiz Duran Atiş
SİSerhan İLKENTAPAR
Serhan İLKENTAPAR
This paper reports the results of an investigation on the influences of admixtures and curing conditions on some properties of Alkali-Activated Slag (AAS) mixtures with no cement. In the study, Shrinkage-Reducing (SRA) and superplasticizing and setretarding (WRRe) admixtures were used. For the slag activation, sodium metasilicate was used at two sodium concentrations, 4% and 6% by mass of slag. Setting time, flow loss of fresh mixtures, and shrinkage strain, carbonation, flexural and compressive strength of hardened mixtures were measured. The test results showed that the admixtures generally had no impact on the setting times of AAS pastes. WRRe increased the flow rate of AAS mortars while SRA partially affected the flow values of AAS mortars. WRRe and SRA did not produce an important difference on the carbonation depths of AAS mortars. However, WRRe and especially SRA admixtures decreased the shrinkage values of AAS mortars. Additionally, curing conditions had a significant effect on the mechanical behavior in the hardened state of AAS mortars compared to Normal Portland Cement (NPC) mortars, and the strength development of AAS mortars at early ages was very fast in comparison with NPC mortars when subjected to elevated temperature.

20 March 2024 in Iranian Journal of Science and Technology, Transactions of Civil Engineering
Verified
Journal Article
Closed access
PDF file
MKMehmet Kaya
Mehmet Kaya
SİSerhan İLKENTAPAR
Serhan İLKENTAPAR
UDUgur DURAK
Ugur DURAK
IAISMAIL ISA ATABEY
ISMAIL ISA ATABEY
SCSERHAT CELIKTEN
SERHAT CELIKTEN

12 May 2023 in Journal of Material Cycles and Waste Management
Verified
Journal Article
Closed access
PDF file
AÖAhmet Özsoy
Ahmet Özsoy
EÖEzgi Örklemez
Ezgi Örklemez
SİSerhan İLKENTAPAR
Serhan İLKENTAPAR

1 January 2019 in Revista de la construcción
Verified
Journal Article
Open access
PDF file
OKOkan Karahan
Okan Karahan
UDUgur DURAK
Ugur DURAK
SİSerhan İLKENTAPAR
Serhan İLKENTAPAR
IAISMAIL ISA ATABEY
ISMAIL ISA ATABEY
CACengiz Duran Atiş
Cengiz Duran Atiş
DOI: 10.7764/RDLC.18.2.386 Behaviour of construction materials i.e. steel, concrete and mortar under elevated temperature is important. In the study, the variations in mass loss, and strengths of polypropylene fiber reinforced mortar subjected to elevated temperatures were examined. Mortar was made with CEM I 42.5R Portland cement, monofilament polypropylene fiber, fine aggregate and drinkable water. The sand-cement and water-cement ratio were chosen 3:1 and 1:2 for all mixtures, respectively. Mixes containing 0, 0.1, 0.2 and 0.3% polypropylene fiber in volume of solid matter of mixture were prepared. Mortars were exposed to 100, 200, 400, 600 and 800°C temperatures and cooled down 23±2°C in air and water. There was a difference between the temperatures at which the important reductions observed for flexural tensile and compressive strength. Significant reduction was observed at 400°C for compressive strength and while it was 200°C for flexural strength. No difference was observed between air cooling and water cooling regimes up to 600°C; however, at 800°C the residual compressive and flexural strength of water cooled mortar was about 40% of the air cooled mortar. Mortar containing polypropylene fiber presented better behaviour to elevated temperature in terms of relative residual strengths up to 400°C.  

1 January 2023 in Revista de la construcción
Verified
Journal Article
Open access
PDF file
YGYusuf Gökşen
Yusuf Gökşen
UDUgur DURAK
Ugur DURAK
SİSerhan İLKENTAPAR
Serhan İLKENTAPAR
IAISMAIL ISA ATABEY
ISMAIL ISA ATABEY
MKMehmet Kaya
Mehmet Kaya
CACengiz Duran Atiş
Cengiz Duran Atiş
In this study the mitigation influence of incorporating waste glass powder (G) and class F fly ash (F) in mortar as partial cement replacement on the alkali-silica reaction (ASR) between reactive aggregate and alkali contents of cement were investigated. Waste G and F replaced cement separately and together on mass basis at 10%, 20%, and 30%. The unit weight (28 days), water absorption, porosity, compressive, and flexural strength tests were conducted at 28- and 90-day water curing time on 40×40×160 mm prismatic hardened samples and flow table test on fresh mortar. There was a slight reduction of the unit weight, an increased workability, and decreased water absorption and porosity; a little reduction of the compressive strength and flexural strength were seen after the tests. In addition, the expansions of mortar were measured up to 90 days. When 14 days expansions were considered according to ASTM C1260, addition of waste G and F separately reduced the expansion that occurred due to ASR. However, the mixture containing 15% waste G and 15% F together (GF-30) exhibited the lowest expansion in the order of 0.02% which was far lower than 0.10%. The higher replacement ratio of waste G and F together and separately caused lower expansion in mortar.