LIN LI

Prof. Dr. LIN LI

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2022 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
LLLIN LI
LIN LI
CLCun-liang Liu
Cun-liang Liu
ZXZhipeng Xu
Zhipeng Xu
HZHui Ren Zhu
Hui Ren Zhu
FZFan Zhang
Fan Zhang
Experimentation research was conducted for studying the effect of blowing ratio (M) as well as cross flow Reynolds number (Rec) on distribution characteristics in film cooling effectiveness and heat transfer coefficient (h) on compound angle hole configuration with applying transient liquid crystal (TLC) technology. The distribution characteristics of discharge coefficient (Cd) were measured by the flow resistance experiment. The net heat flux reduction (NHFR) is applied for assessing the film cooling performance. Numerical simulation was carried out to present the flow features for analyzing the film cooling mechanism. Results demonstrate that the measured Cd shows upward tendency with the increase of M and is almost no change until M increases to a certain extent. At small M, the measured film cooling effectiveness is higher and descends with the increase of Rec. At the large M, the measured film cooling effectiveness is lower and presents the slight influence on the rises with the increase of Rec. The increase of M makes the measured h descend. The increase of Rec makes the measured h rise. And the NHFR shows the decreasing tendency with the increasing M. A The NHFR decreases in the increase of Rec at M=0.5 and M=2.0. The increase of Rec presents the slight influence on the NHFR under the condition of M =1.0.

1 December 2023 in Physics of Fluids
Verified
Journal Article
Open access
PDF file
BLBingran Li
Bingran Li
CLCun-liang Liu
Cun-liang Liu
LLLIN LI
LIN LI
JLJiebo Li
Jiebo Li
WXWeijiang Xu
Weijiang Xu
The present study is focused on the problems of gas–solid two-phase flow transport in the film cooling hole that cause film flow obstruction and cooling failure. To study the unsteady development process of the deposition layer in the film hole, a simulation method combining computational fluid dynamics and the discrete element method was used, and a film hole flow model was established. The effect of gas phase and solid phase characteristics on clogging and deposition in the film hole was studied. The following conclusions are drawn: The inlet/outlet pressure ratio is inversely proportional to the clogging degree of the film hole. The inlet/outlet pressure determines the deposition behavior by affecting the initial momentum and drag force of particles. In the Stokes number range of 1.58–14.26, the deposition in the film hole first increases and then decreases. There is a Stokes number with the most severe clogging. The Stokes number determines the deposition pattern by affecting the relative magnitudes of the drag force and interaction forces of particles. The particle surface energy is positively correlated with film hole clogging. The particle surface energy determines the stability of the deposition layer by influencing the strength of the force chain network.

27 February 2026 in Results in Engineering
Verified
Journal Article
Open access
LLLIN LI
LIN LI
TYTianhao Yong
Tianhao Yong
MSMing Sun
Ming Sun
JLJie Liu
Jie Liu

9 July 2026 in Thermal Science and Engineering Progress
Verified
Journal Article
Open access
LLLIN LI
LIN LI
TYTianhao Yong
Tianhao Yong
CLCunliang Liu
Cunliang Liu
ZCZhuchuan Chang
Zhuchuan Chang
ZZZhiteng Zhang
Zhiteng Zhang

1 July 2026 in Physics of Fluids
Verified
Journal Article
Closed access
CZChang Zhuchuan
Chang Zhuchuan
HWHaiou Wang
Haiou Wang
SGShibo Gu
Shibo Gu
LLLIN LI
LIN LI
Kun LuoKun Luo
Kun Luo
JFJianren Fan
Jianren Fan
Direct numerical simulations are performed to investigate the ignition process of lean hydrogen/air mixtures in a model combustor with three linearly arranged swirling burners. Ignition is initiated in the internal recirculation zone of the central burner and evolves through three characteristic stages: an initial flame-growth stage following kernel establishment, a flame-reorganization stage, and a near-stabilized stage. The flame propagation is strongly flow controlled and markedly asymmetric, leading to earlier ignition of the right neighboring burner. The results show that the ignition dynamics are governed by a change in the local flame-surface balance. At the early stage, the flame stretch is positive and dominated by tangential strain, which promotes flame-surface production and rapid flame growth. As ignition proceeds, the curvature-stretch contribution becomes increasingly negative and is controlled mainly by the curvature-diffusion term, leading to flame reorganization and a reduction in the overall flame area. Principal curvature analysis further shows that the flame-surface topology evolves from a state dominated by leading-edge-type geometries to one increasingly dominated by trailing-edge-type geometries. However, fuel consumption analysis reveals that geometrically dominant regions and regions contributing most strongly to fuel consumption do not fully coincide, since leading-edge-type structures remain major contributors to fuel consumption until the near-stabilized stage.

20 August 2026 in Processes
Verified
Journal Article
Open access
PDF file
CZChang Zhuchuan
Chang Zhuchuan
ZJZhe Jiang
Zhe Jiang
ZZZhiteng Zhang
Zhiteng Zhang
LLLIN LI
LIN LI
Compared with single-swirl configurations, linearly arranged multi-swirl burners introduce complex inter-jet interactions that significantly alter flame dynamics; however, the underlying mechanisms remain poorly understood. In this study, direct numerical simulation (DNS) is employed to investigate a lean-hydrogen multi-swirl flame, aiming to elucidate its flame structure and dynamic evolution. The flame development region is divided into upstream (Region 1) and downstream (Region 2) regions, based on the critical location where the flame stretch transitions from positive to negative. The flow field, flame morphology, thickness, stretch, curvature, and their joint statistical relationships are systematically compared between the two regions. The results show that in Region 1, the flame stretch is dominated by positive strain rate, and the flame maintains a continuous structure and a small thickness. In Region 2, the curvature stretch becomes dominant, leading to severe flame wrinkling, local extinction and breakup, with the mean flame thickness increasing to about 1.5 times that of the laminar flame. Joint PDF analyses reveal that negative flame stretch is correlated with a large negative curvature in Region 2, whereas in Region 1, it is not affected by the curvature sign. The downstream flame also exhibits higher displacement speeds, indicating intensified turbulence–flame interaction. This study reveals the streamwise transition mechanism of the multi-swirl flame from strain-dominated to curvature-dominated dynamics, clarifies the distinct coupling modes of upstream stabilization and downstream fragmentation, and provides new theoretical guidance for stable combustion and wide-operability design of lean-hydrogen swirl combustors.