Luis Sousa

Prof. Luis Sousa

orcid

Research Focus & Metrics

Academic Career Length

31Years (1996-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2019 in Science of The Total Environment
Verified
Journal Article
Closed access
RVRoberto A. Varella
Roberto A. Varella
MFMarta V. Faria
Marta V. Faria
PMPablo Mendoza-Villafuerte
Pablo Mendoza-Villafuerte
Patricia BaptistaPatricia Baptista
Patricia Baptista
LSLuis Sousa
Luis Sousa
Gonçalo DuarteGonçalo Duarte
Gonçalo Duarte

12 September 2018 in Applied Sciences
Verified
Journal Article
Open access
PDF file
RVRoberto Aliandro Varella
Roberto Aliandro Varella
BGBarouch Giechaskiel
Barouch Giechaskiel
LSLuis Sousa
Luis Sousa
Gonçalo DuarteGonçalo Duarte
Gonçalo Duarte
Real-driving emissions (RDE) testing with portable emissions measurement systems (PEMS) during the type approval and in-service conformity of light-duty vehicles was recently introduced in the European Union legislation. In this paper, three PEMS were compared with laboratory analyzers connected to the tailpipe and the dilution tunnel. The tests were conducted with two Euro 6 vehicles (one gasoline and one diesel) performing the World harmonized Light vehicles Test Cycle (WLTC) and a pre-recorded RDE cycle on a chassis dynamometer. The results showed that the differences of the PEMS gas analyzers compared to the laboratory references were typically within 2% for CO2 and 5% for NOx. The CO2 and NOx mass emissions were within 10% and 15%, respectively, with only a few exceptions. The exhaust flow rate measurements were within 10% at low speeds (urban conditions), and 5% at higher speeds. These results confirm the legislated permitted tolerances and the 2017 PEMS uncertainty estimates.

20 September 2007 in Multibody System Dynamics
Verified
Journal Article
Closed access
PDF file
LSLuis Sousa
Luis Sousa
PVPaulo Veríssimo
Paulo Veríssimo
JAJorge Ambrósio
Jorge Ambrósio

28 March 2017 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
PDF file
RVRoberto Aliandro Varella
Roberto Aliandro Varella
Gonçalo DuarteGonçalo Duarte
Gonçalo Duarte
Patricia BaptistaPatricia Baptista
Patricia Baptista
LSLuis Sousa
Luis Sousa
PVPablo Mendoza Villafuerte
Pablo Mendoza Villafuerte
The gap between regulated emissions from vehicle certification procedures and real-world driving has become increasingly wider, particularly for nitrogen oxides (NOx). Even though stricter emission regulations have been implemented, NOx emissions are dependent on specific, short-duration driving events which are difficult to control, therefore high concentrations of these pollutants are still being measured in European cities. Under certification procedures, vehicle emissions compliance is evaluated through standards, recurring to driving cycles performed on chassis dynamometer under controlled laboratory conditions. Different countries use different standard cycles, with the US basing their certification cycle on FTP-75 and Europe using NEDC (Euro 5/6c)/WLTP (Euro 6d). However, the representativeness of standard driving cycles has been under discussion and, consequently, new updates on the light duty regulation from the European Commission include a Real Driving Emissions (RDE) Regulation, establishing that vehicle emissions must be measured on the road with a Portable Emission Measurement System (PEMS). However, RDE tests have shown weak points, namely regarding testing boundary conditions and data analysis methods. Moreover, reproducibility of tests is hardly achievable and both dynamic and environmental boundaries (such as ambient condition, route, etc.) are unique for a specific geographical location, which can be representative for one location but not for another test-site. On-road data analysis methodology is defined by the European Commission, with two main methods are being tested: the Moving Averaging Window (MAW); and the Power Binning (PB). As result, the scope of this study was to evaluate the RDE data analysis methods, including the Vehicle Specific Power methodology (used on MOVES model), applied to 1 Hz on-road data from 3 vehicle propulsion technologies (spark-ignition, compression-ignition and hybrid), collected in Lisbon, Portugal. This approach allowed analyzing and identifying the differences between the methods for each vehicle propulsion technology. Regarding total CO2 emissions and NOx emissions, the application of the methods indicates that the MAW provides an overall difference of around 7% for CO2 and 10% for NOx comparing with the PB method. The PB is conceptually similar to VSP, although an overall 10% for CO2 and 19% for NOx difference was found. Differences on the methods results are due to the use of different approaches and, consequently, lead to different results, which are more explained on this paper.

1 January 2016 in Procedia Structural Integrity
Verified
Journal Article
Open access
BSBruno Soares
Bruno Soares
RPR. Preto
R. Preto
LSLuis Sousa
Luis Sousa
LRLuis Reis
Luis Reis
With the increasing interest in sustainable solutions in material design in the last decade, research on natural materials (animal, vegetal or mineral) has increased at a rapid pace. Of these materials, Basalt Fibers for composite construction provide an interesting set of mechanical properties, equal or above to those of Glass Fibers, with advantages in terms of cost effectiveness and production to vegetable based Natural Fibers. Basalt fibers offer some advantages versus current materials, it is fireproof, requires no material addition, has better mechanical properties than most types of E-Glass, and it is cheaper than Carbon Fiber. This paper studies the mechanical properties of a Basalt Fiber composite in an Unsaturated Polyester matrix produced by Resin Transfer Molding (RTM), with the composites subjected to tensile, compression, shear and flexural tests. The results aligned with the predicted values by using the mixing rule, albeit with a high coefficient of variation, which microscopic analysis confirmed to arise from production issues with RTM

1 January 2010 in Archive of Mechanical Engineering
Verified
Journal Article
Closed access
PDF file
RPRicardo José Fontes Portal
Ricardo José Fontes Portal
JDJoão Manuel Pereira Dias
João Manuel Pereira Dias
LSLuis Sousa
Luis Sousa