In 2011, the European Commission introduced a limit for nonvolatile particle number (PN) emissions >23 nm from light-duty (LD) vehicles and the stated intent is to implement similar legislation for on-road heavy-duty (HD) engines at the next legislative stage. This paper reviews the recent literature regarding the operation-dependent emission of PN from LD vehicles and HD engines, and the measurement procedure used for regulatory purposes. The repeatability of the PN method is of the order of 5% and higher scatter of the results can easily be explained by the effect of the vehicles or the aftertreatment devices on the PN emissions (e.g., the fill state of the diesel particulate filters). Reproducibility remains an issue since it may exceed 30%. These high-variability levels are mainly associated with calibration uncertainties of the PN instruments. Correlation measurements between the full-flow dilution tunnels (constant-volume samplers, CVS) and the proportional partial-flow dilution systems (PFDS) showed agreement within 15% for the PN method down to 1 × 10¹¹ p/kWh. At lower concentrations, the PN background of the CVS and/or the PFDS can result in larger inconsistencies. The filter-based particulate matter (PM) mass and the PN emissions correlate well down to 1–2 mg/km for LD vehicles and to 2–3 mg/kWh for HD applications. The correlation improves when only elemental carbon mass is considered: it is relatively good down to 0.1–0.3 mg/km or mg/kWh. Copyright 2012 American Association for Aerosol Research

Tyre particles are generated by shear forces between the tread and the road or by volatilisation. Tyre abrasion (wear) contributes from one-third to half of microplastics unintentionally released into the environment. The major part ends up in the soil, a considerable amount is released into the aquatic environment, and a small percentage becomes airborne. Nevertheless, tyre abrasion contributes to 5–30% of road transport particulate matter (PM) emissions. This corresponds to approximately 5% of total ambient PM emissions. The particle mass size distribution peak at around 20 to 100 μm, with a second peak in the 2–10 μm range. A nucleation mode has been reported in some studies. The absolute abrasion levels depend on the tyre, vehicle, and road characteristics, but also on environmental conditions and driving style. Most tyre particle emission factors in the literature are based on data prior to the year 2000. We aggregated recent studies and found a mean abrasion of 110 mg/km per vehicle or 68 mg/km/t for passenger cars (based on approximately 300 measurements). Based on a limited number of studies, the PM₁₀ emissions were 1.4–2.2 mg/km per tyre. On the other hand, the particle number emissions were in the order of 10¹⁰ #/km per tyre. The ratio of PM₁₀ to total abrasion was found to be 2.5% on average. Finally, the ratio of PM_2.5 to PM₁₀ was calculated to be around 40%. Various mitigation measures for tyre particle pollution could be envisaged; the most direct is the limitation of the tyre abrasion rate, as proposed by the European Commission for the Euro 7 regulation. Other regulatory initiatives are also discussed.

European regulation 2016/427 (the first package of the so-called Real-Driving Emissions (RDE) regulation) introduced on-road testing with Portable Emissions Measurement Systems (PEMS) to complement the chassis dynamometer laboratory (Type I) test for the type approval of light-duty vehicles in the European Union since September 2017. The Not-To-Exceed (NTE) limit for a pollutant is the Type I test limit multiplied by a conformity factor that includes a margin for the additional measurement uncertainty of PEMS relative to standard laboratory equipment. The variability of measured results related to RDE trip design, vehicle operating conditions, and data evaluation remain outside of the uncertainty margin. The margins have to be reviewed annually (recital 10 of regulation 2016/646). This paper lays out the framework used for the first review of the NOx margin, which is also applicable to future margin reviews. Based on experimental data received from the stakeholders of the RDE technical working group in 2017, two NOx margin scenarios of 0.24-0.43 were calculated, accounting for different assumptions of possible zero drift behaviour of the PEMS during the tests. The reduced uncertainty margin compared to the one foreseen for 2020 (0.5) reflects the technical improvement of PEMS over the past few years.

The particulate matter (PM) emissions of gasoline vehicles were much lower than those of diesel vehicles until the introduction of diesel particulate filters (DPFs) in the early 2000s. At the same time, gasoline direct injection (GDI) engines started to become popular in the market due to their improved efficiency over port fuel injection (PFI) ones. However, the PM mass and number emissions of GDI vehicles were higher than their PFI counterparts and diesel ones equipped with DPFs. Stringent PM mass levels and the introduction of particle number limits for GDI vehicles in the European Union (EU) resulted in significant PM reductions. The EU requirement to fulfill the proposed limits on the road resulted to the introduction of gasoline particulate filters (GPFs) in EU GDI models. This review summarizes the evolution of PM mass emissions from gasoline vehicles placed in the market from early 1990s until 2019 in different parts of the world. The analysis then extends to total and nonvolatile particle number emissions. Care is given to reveal the impact of ambient temperature on emission levels. The discussion tries to provide scientific input to the following policy-relevant questions. Whether particle number limits should be extended to gasoline PFI vehicles, whether the lower limit of 23 nm for particle number measurements should be decreased to 10 nm, and whether low ambient temperature tests for PM should be included.