Kae Nakamura

Ms. Kae Nakamura

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 November 2024 in Acta Materialia
Verified
Journal Article
Closed access
YSYeongwoo Son
Yeongwoo Son
SUStanislav Udovenko
Stanislav Udovenko
SASai Venkata Gayathri Ayyagari
Sai Venkata Gayathri Ayyagari
JBJohn P. Barber
John P. Barber
KNKae Nakamura
Kae Nakamura
STSusan Trolier-McKinstry
Susan Trolier-McKinstry

19 January 2026 in Applied Physics Letters
Verified
Journal Article
Closed access
RKRokhyeon Kim
Rokhyeon Kim
DBDonggeon Baek
Donggeon Baek
BDBurcu Dursun
Burcu Dursun
DHDayeong Hur
Dayeong Hur
KNKae Nakamura
Kae Nakamura
JRJungho Ryu
Jungho Ryu
Adhesive-free 2-2 structured Ni/Pb(Mg1/3Nb2/3)O3–PbZrTiO3/Ni laminates were realized by directly electroplating magnetostrictive Ni onto [011]-oriented Pb(Mg1/3Nb2/3)O3-Pb(Zr,Ti)O3 (PMN-PZT) single crystals for operation in the d32 mode, thereby maximizing interfacial bonding and suppressing viscoelastic coupling losses associated with polymer adhesive layers. Finite element analysis comparing the presence/absence of an interlayer, single crystal vs ceramic piezoelectrics, and variations in Ni thickness shows that removing a polymeric adhesive layer increases the induced piezoelectric potential by approximately 13% that single crystals deliver ∼1.3 times higher output than ceramics at identical Ni thickness, and that the response grows, then saturates with Ni thickness under the same excitation condition. Uniform polycrystalline Ni layers with soft magnetic characteristics and controlled thickness were obtained by direct Ni electroplating on PMN-PZT single crystals. Under off-resonance condition, the direct magnetoelectric voltage coefficient increases with Ni thickness and reaches 6.9 V/cm Oe at bias fields below 100 Oe. At the electromechanical resonance, the coefficient is strongly amplified to 1419 V/cm Oe. These results indicate that combining direct Ni electroplating on 32 mode single crystals enhances interfacial stress transfer and magneto-electromechanical conversion, providing a scalable route to high magnetoelectric responses for sensitive magnetic field sensing, low-frequency magnetoelectric antennas, and other applications.

23 June 2026 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
SASengsavang Aphayvong
Sengsavang Aphayvong
AVAbhyuday Verma
Abhyuday Verma
KNKae Nakamura
Kae Nakamura
AAAli Habib Akhyari
Ali Habib Akhyari
TYTakeshi Yoshimura
Takeshi Yoshimura
BABetul Akkopru Akgun
Betul Akkopru Akgun
The long-term reliability of Mn-doped BiFeO3 thin films remains a key challenge for their implementation in piezoelectric microelectromechanical systems. In this work, the electronic transport mechanisms and DC resistance degradation of (100) Mn-doped BiFeO3 (BFMO) epitaxial films grown on (100) Si substrates by RF magnetron sputtering were systematically investigated. The leakage current characteristics exhibit a strong polarity dependence, originating from a nonuniform distribution of oxygen vacancies across the film thickness. Under field-up bias, where a high concentration of oxygen vacancies is present near the top interface, leakage is dominated by Poole–Frenkel emission from VÖ related traps in the low-field regime and evolves into trap-controlled space-charge-limited conduction at higher fields, with transport controlled by FeFe′ sites. In contrast, under field-down bias, where the VÖ concentration near the bottom interface is comparatively low, transport is Ohmic at low electric fields and transitions to Poole–Frenkel emission at higher fields, with conduction governed primarily by FeFe′ trap levels. The asymmetric VO·· distribution also gives rise to polarity-dependent DC resistance degradation, governed by field-driven VÖ drift and subsequent accumulation at the cathode interface. Since the [VÖ] is initially higher near the top interface, VÖ redistribution proceeds more rapidly, resulting in accelerated degradation kinetics and a reduced lifetime. The extracted VÖ diffusion coefficient for BFMO (∼2.7 × 10–14 cm2 s–1) is approximately an order of magnitude higher than values reported for PZT films, consistent with the comparatively shorter lifetime observed under similar stress conditions. These findings highlight the pivotal role of defect engineering particularly in controlling oxygen vacancy concentration and migration for optimizing the reliability and performance of BiFeO3-based MEMS devices.

5 April 2026 in Sensors
Verified
Journal Article
Open access
PDF file
KNKae Nakamura
Kae Nakamura
CHChi-Luen Huang
Chi-Luen Huang
AAAli Habib Akhyari
Ali Habib Akhyari
AAAndrea P. Argüelles
Andrea P. Argüelles
TJThomas N. Jackson
Thomas N. Jackson
STSusan Trolier-McKinstry
Susan Trolier-McKinstry
A bottom-up fabrication approach for flexible piezoelectric micromachined ultrasound transducer (PMUT) arrays on stainless-steel substrates was developed. Devices were fabricated using chemical solution deposition of a 700 nm-thick layer of Pb0.99□0.01(Zr0.52Ti0.48)Nb0.02O3, where □ denotes a vacancy on the Pb site, on 50 μm-thick LaNiO3/HfO2/stainless-steel foils. Lithography for definition of the electrode and piezoelectric layers was completed on the front of the wafer. Ni electroplating on the back side of the foil was used to create locally stiff areas to define the deflection area. PMUT devices were successfully fabricated using this method. The permittivity and loss tangent of the fabricated device at 1 kHz were 283 ± 9 and <1.5%, respectively. The remanent polarization was measured to be 38 ± 0.3 μC/cm2.