Zn0.64Mg0.36O (ZMO) is a newly discovered ferroelectric oxide with the wurtzite structure. Epitaxial Zn0.64Mg0.36O films from 0.036 to 0.5 μm in thickness are grown on Pt/sapphire with the crystallographic c-axis out of plane. At room temperature, the remanent polarization is ∼80 μC/cm2 and the coercive field is ∼3 MV/cm. The coercive field is strongly temperature dependent up to 240 °C with a pseudo-activation energy of 23 ± 0.3 meV, suggesting that polarization reversal occurs through an extrinsic process such as domain wall motion. ZMO films can be woken up in 20 electric field cycles on driving near the coercive field; they wake up in a single loop at fields in excess of 4 MV/cm. A thermally activated fluid imprint process, with a pseudo-activation energy of 67 ± 8 meV, enlarges the coercive field by several hundred kV cm−1 after switching the polarization. Additionally, ZMO films exhibit excellent retention characteristics; no reduction in the polarization is observed up to 1000 h from room temperature to 200 °C bakes. This current early generation of ZMO films can survive several thousand switching cycles before dielectric breakdown occurs.
The correlation between defect chemistry, leakage currents, and time-dependent dielectric breakdown was studied for PbZr0.52Ti0.48O3 (PZT) films doped with 0.5, 1, 2, or 4 mol. % Nb. As the samples are nearly intrinsic (that is, close to n- to p-type transition), signatures for both hole hopping between Pb2+ and Pb3+ and electron trapping by Ti4+ were observed. For all doping levels, the dominant conduction mechanism transitioned from Poole–Frenkel emission at lower electric fields to Schottky emission at higher electric fields. The electric field for this transition diminishes from 172 to 82 kV/cm with decreasing Nb concentration. The concomitant modification of the Schottky barrier height from 1.24 to 0.95 eV with decreasing Nb concentration is attributed to Fermi level pinning via oxygen vacancies. The DC resistance degradation was controlled by Schottky emission from 250 to 400 kV/cm. It was found that the lifetime of the films increases with increasing the Nb level. The effective Schottky barrier height for 2 mol. % Nb-doped PZT films decreased from 1.12 to 0.85 eV during degradation. This is related to the movement of oxygen vacancies toward the cathode and the observation of Ti3+ near the cathode, which are proved via thermally stimulated depolarization current and electron energy loss spectroscopy, respectively. Furthermore, Schottky emission starts to control the conduction at lower electric fields after degradation as a result of oxygen vacancy accumulation near the cathode. This, in turn, decreases the potential barrier height for electron injection from the Pt electrode into the PZT films. The mechanisms for time-dependent dielectric breakdown in PZT films will thus be a strong function of the initial oxygen vacancy concentration and its distribution within the PZT films.
The role of interfacial defect chemistry in time dependent breakdown and associated charge transport mechanisms was investigated for Pb0.99(Zr0.52Ti0.48)0.98Nb0.02O3 (PNZT) films. Electrical degradation was strongly dependent on the sign of the electric field; a significant increase in the median time to failure from 4.8 ± 0.7 to 7.6 ± 0.4 h was observed when the top electrode was biased negatively compared to the bottom electrode. The improvement in the electrical reliability of Pt/PNZT/Pt films is attributed to (1) a distribution across the film due to PbO nonstoichiometry and (2) Ti/Zr segregation in PNZT films. Compositional mapping indicates that PbO loss is more severe near the bottom electrode, leading to a gradient across the film thickness. Upon degradation, migration toward the bottom Pt electrode is enhanced. The concentration of accumulated near the bottom Pt interface (6.2 × 1018/cm3) after degradation under an electric field of 350 kV/cm for 12 h was two times higher than that near the top Pt/PNZT interface (3.8 × 1018/cm3). The accumulation near the bottom Pt/PNZT interface causes severe band bending and a decrease in potential barrier height, which in turn accelerates the electron injection, followed by electron trapping by Ti4+. This causes a dramatic increase in the leakage current upon degradation. In contrast to the bottom Pt/PNZT interface, only a small decrease in potential barrier height for electron injection was observed at the top Pt/PNZT interface following degradation. It is also possible that a Zr-rich layer near the top interface reduces electron trapping by Ti4+.
31 July 2015 in Journal of the American Ceramic Society