Jianwei Teng

Dr. Jianwei Teng

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 June 2024 in Transactions of Nonferrous Metals Society of China
Verified
Journal Article
Open access
PZPing Zhang
Ping Zhang
XYXiao-Bo Yuan
Xiao-Bo Yuan
ZZZi-Ming Zeng
Zi-Ming Zeng
JTJianwei Teng
Jianwei Teng
YZYunhe Zhou
Yunhe Zhou
Yunping LiYunping Li
Yunping Li

31 January 2022 in Advanced Powder Technology
Verified
Journal Article
Closed access
XGXiaojuan Gong
Xiaojuan Gong
JLJiapeng Liu
Jiapeng Liu
JTJianwei Teng
Jianwei Teng
XYXianjue Ye
Xianjue Ye
Zhongchang WangZhongchang Wang
Zhongchang Wang
Yunping LiYunping Li
Yunping Li

17 June 2024 in Materials
Verified
Journal Article
Open access
PDF file
CLChao Li
Chao Li
ZZZiming Zeng
Ziming Zeng
JTJianwei Teng
Jianwei Teng
BYBiaobiao Yang
Biaobiao Yang
Yunping LiYunping Li
Yunping Li
In this study, the ball-on-disk sliding wear and tribocorrosion behavior in the H2SO4 and HCl solution of NiCoCrMoCu alloys with carbon additions of 0.2, 1, 1.5, and 2 wt.% with the Al2O3 ball as a counterpart was investigated systematically. Obvious tribocorrosion antagonistic effects were found after wear in both aqueous solutions. Compared with dry sliding wear conditions, the lubrication effect of the aqueous solution significantly reduces the wear rate of the alloy, and the reduction effect in the H2SO4 aqueous solution was more obvious than that in HCl. The antagonistic effects of the 0.2C and 1C alloys decrease with the load and sliding rate, while those of the 1.5C and 2C alloys increase. The (coefficient of friction) COF and wear rate under different loads and sliding rates were analyzed using the response surface analysis (RSM) method. It was found that the COF mainly showed dependence on the sliding rate, while the wear rate showed dependence on load and sliding speed.

2 March 2026 in Materials
Verified
Journal Article
Open access
PDF file
XDXiaoxuan Dong
Xiaoxuan Dong
YLYidi Li
Yidi Li
RSRongrong Shang
Rongrong Shang
MCMengxia Chen
Mengxia Chen
LLLu Liu
Lu Liu
Yunping LiYunping Li
Yunping Li
In this study, Inconel 600 alloy with reductions of 20%, 50%, and 80% was obtained through cold rolling, and the effects of plastic deformation on its mechanical properties and corrosion behavior in a hydrofluoric acid (HF) solution were systematically investigated. The results show that cold rolling induces pronounced work hardening, with both hardness and strength increasing continuously with increasing reduction, while the ductility decreases accordingly. The alloy with 80% reduction exhibits the highest strength, with an ultimate tensile strength of 1270 MPa and a yield strength of 1210 MPa. In contrast, the macroscopic corrosion resistance of the alloy in HF solution remains essentially unchanged with increasing deformation, although a slight intensification of pitting corrosion is observed. The combined effects of deformation-induced pitting and passivation enhancement resulted in retention of corrosion resistance. These findings demonstrate that appropriate control of cold rolling enables effective mechanical strengthening of Inconel 600 without significantly sacrificing its corrosion performance in aggressive fluorine containing environments.

2 September 2025 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
CLChao Li
Chao Li
ZZZiming Zeng
Ziming Zeng
JTJianwei Teng
Jianwei Teng
XGXiaojuan Gong
Xiaojuan Gong
Yunping LiYunping Li
Yunping Li