An optically addressed liquid crystal modulator for wavefront control of 1053 nm laser beam is reported in this paper. Its working principle, control method and spatial phase modulation capability are mainly introduced. A new method of measuring the relationship between gray level and phase retardation is proposed. The rationality of the curve is further confirmed by designing special experiments. According to the curve, several spatial phase distributions have been realized by this home-made device. The results show that, not only the maximum phase retardation is larger than $2\unicode[STIX]{x03C0}$ for 1053 nm wavelength, but also the control accuracy is high. Compared with the liquid crystal on silicon type spatial light modulator, this kind of modulator has the advantages of generating smooth phase distribution and avoiding the black-matrix effect.

In order to improve the damage threshold and enlarge the aperture of a laser beam shaper, photolithographic patterning technology is adopted to design a new type of liquid crystal binary mask. The inherent conductive metal layer of commercial liquid crystal electro-optical spatial light modulators is replaced by azobenzene-based photoalignment layers patterned by noncontact photolithography. Using the azobenzene-based photoalignment layer, a liquid crystal binary mask for beam shaping is fabricated. In addition, the shaping ability, damage threshold, write/erase flexibility and stability of the liquid crystal binary mask are tested. Using a 1 Hz near-IR (1064 nm) laser, the multiple-shot nanosecond damage threshold of the liquid crystal mask is measured to be higher than $15~\text{J}/\text{cm}^{2}$ . The damage threshold of the azobenzene-based photoalignment layer is higher than $50~\text{J}/\text{cm}^{2}$ under the same testing conditions.

In this paper, the feasibility of a high laser damage threshold liquid crystal spatial light modulator based on gallium nitride (GaN) transparent conductive electrodes is proved. The laser-induced damage threshold (LIDT) is measured, and a high LIDT reflective optically addressed liquid crystal light valve (OALCLV) based on GaN is designed and fabricated. The proper work mode of the OALCLV is determined; the OALCLV obtained a maximum reflectivity of about 55% and an on–off ratio of 55:1, and an image response is demonstrated.

Liquid crystal spatial light modulators (LC-SLMs) are devices that can accurately adjust the parameters of beam amplitude, phase, wavefront and polarization. However, due to the limitation of laser damage resistance of component materials, LC-SLMs still have difficulty meeting the application and development needs of a high-average power laser system. Here, we proposed an optically addressable spatial light modulator (OASLM) based on a sapphire substrate. Due to the good thermal conductivity of sapphire, the laser damage resistance of the device was greatly improved. The thermal distribution of OASLM based on the sapphire substrate and the K9 substrate is analyzed by a laser-induced temperature rise model. The experimental results also show the excellent performance of sapphire OASLM under high-power CW laser irradiation, its laser power density is increased from 10 W/cm² to 75 W/cm², and the working time is more than 30 min. By bonding sapphire to the other side, the laser power density can be increased to 100 W/cm², and these are completed without active heat dissipation. This method provides a feasible path for high-average-power SLMs.

The influence of driving conditions on the phase-modulation ability of an optically addressable spatial-light modulator (OASLM) is investigated using an equivalent circuit method and a system for measuring wave-front modulation that uses a phase-unwrapping data-processing method, and is constructed with a charge-coupled device and wave-front sensor. 1λ peak-to-valley phase change for a 1053 nm laser beam is acquired with the home-made OASLM at the optimal driving voltage of 14 V at 200 Hz. The detection system for wave-front modulation has a spatial resolution of 200 µm for binary images and a minimum distinguishable contrast of 1 mm. On-line phase modulation with feedback control can be acquired with the OASLM and the corresponding measuring system.

In this letter, we report a multifunctional high-performance Nd:glass laser system. Laser pulses from an all-fiber front end are first amplified by a regenerative amplifier to 10 mJ level, and then further amplified in a four-pass amplifier. The laser system can provide 10.3-J, 3-ns laser pulses at 1053-nm wavelength. The shot-to-shot energy stability is better than 1.5% (RMS). The output laser beam is near diffraction limit. Binary amplitude masks are used to maintain a flat top near-field profile with a 71% fill factor. After the frequency conversion process, 7 and 5.5 J pulses at 526.5 and 351 nm are obtained, respectively.