Ludwig Jansen van Vuuren

Dr. Ludwig Jansen van Vuuren

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 November 2019 in Journal of the Royal Society of New Zealand
Verified
Journal Article
Closed access
LVLudwig Jansen van Vuuren
Ludwig Jansen van Vuuren
JBJonathan M, Broadbent
Jonathan M, Broadbent
WDWarwick John Duncan
Warwick John Duncan
JWJohn Neil Waddell
John Neil Waddell
All‐ceramic dental restorations are now regularly being used in clinical situations. Forces applied to ceramic dental restorations can result in failure due to cracking. Dental restorations may be subjected to significant loads in the mouth and small contact points between opposing teeth may result in markedly high stress when a high bite force is encountered. This study recorded maximum voluntary bite forces on the posterior teeth of 40 participants and inter‐occlusal contact points were identified by digitally scanning the teeth and calculating the surface area by accompanying software. Bite forces from as low as 83.9 Newton (N) to the highest at 1642.8 N, with a mean of 430.4 N (sd = 279.4) were recorded. Inter‐occlusal contact points as small as 0.065 mm 2 were measured. The resultant stress teeth may experience has been shown to potentially exceed the flexural strength of even the strongest dental ceramic available on the market for 21.8% of the teeth tested. This study aimed to describe the stresses that teeth experience, and thus predict the stresses that future restorations on those teeth may experience. This approach may prove valuable in guiding clinicians in their material selection as well as the design of all‐ceramic restorations.

1 September 2020 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Closed access
LVLudwig Jansen van Vuuren
Ludwig Jansen van Vuuren
WVW.A. Jansen van Vuuren
W.A. Jansen van Vuuren
JBJ.M. Broadbent
J.M. Broadbent
WDW.J. Duncan
W.J. Duncan
JWJ.N. Waddell
J.N. Waddell

1 January 2010 in Dental Materials Journal
Verified
Journal Article
Open access
PDF file
LHLihong He
Lihong He
LVLudwig Jansen van Vuuren
Ludwig Jansen van Vuuren
NPNina Planitz
Nina Planitz
MSMichael V. Swain
Michael V. Swain
The purpose of this study was to investigate the properties of a die hardener penetrated layer and evaluate its protective effects on the surface of die stone. A commercial die hardener (PDQ die hardener, Whipmix corp., USA) was tested on a die stone (GC Fujirock® EP die stone, GC Europe, Belgium) and a dental plaster (Dental Stone, United States Gypsum Company, USA). Nanoindentation and micro-scratch tests were performed on both coated and uncoated specimens. The scratch damage was observed by SEM and the penetration depth of die hardener was detected by the affiliated EDX. Upon drying, the die hardener penetrated into the die stone to a depth of 3-5 μm, and deposited a thin film on the surface of die stone. Although the die hardener penetrated layer did not show improved mechanical properties, the die hardener film on the surface did protect the specimens from abrasion damage.

19 August 2023 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Open access
LVLudwig Jansen van Vuuren
Ludwig Jansen van Vuuren
WVW.A. Jansen van Vuuren
W.A. Jansen van Vuuren
JBJ.M. Broadbent
J.M. Broadbent
WDW.J. Duncan
W.J. Duncan
JWJ.N. Waddell
J.N. Waddell
The periodontium is a biological structure that supports the tooth in the jaw and behave as a developmental, biological, and functional unit. Teeth may be considered to be 'suspended' in their tooth sockets which provides teeth the ability to move in response to an applied load. In terms of the protection the suspension effect of the periodontal ligament may offer dental restorations, movement in an axial direction is of interest. No device or system to measure this movement is readily available, thus a novel approach had to be developed to address the questions of this research. The device developed allowed images to be taken of the participants teeth before, during and after a participant bit down on the tooth and used to measure the displacement of the tooth in image processing software. Average maximum tooth displacement from all participants of 73.8 μm (sd = 22.5 μm) were recorded. Longer application time of bite force was associated with greater cumulative tooth displacement, for a given level of force, and female participants experienced approximately 2 μm more displacement per Newton than males. The device and methods utilised in this study has shown good potential as a measurement protocol for measurement of vertical tooth movements in vivo. The response to load the teeth in this study has shown, highlighted the visco-elastic properties of the periodontal ligament and the amount of movement recorded supports the protection that controlled tooth movement offers teeth.

9 June 2020 in International Journal of Paediatric Dentistry
Verified
Journal Article
Closed access
PDF file
Carolina LochCarolina Loch
Carolina Loch
LVLudwig Jansen van Vuuren
Ludwig Jansen van Vuuren
WDWarwick John Duncan
Warwick John Duncan
DBDorothy H. Boyd
Dorothy H. Boyd
LPLyndie Foster Page
Lyndie Foster Page

1 January 2020 in Heliyon
Verified
Journal Article
Open access
VMVidya Latchmi Mudliar
Vidya Latchmi Mudliar
KLKai Chun Li
Kai Chun Li
LVLudwig Jansen van Vuuren
Ludwig Jansen van Vuuren
JWJohn Neil Waddell
John Neil Waddell
To evaluate the elastic recovery of a typical irreversible hydrocolloid impression material in terms of the amount of undercut identified and additional thickness of spacer provided before custom tray fabrication. This study surveyed the undercut depths of the teeth surfaces and lingual sulci of one hundred partially dentate mandibular dental casts which were subsequently scanned and the data exported as STL files. A typical cast from each undercut category (0.5mm, 1mm, 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm) was 3D printed. Three custom trays were constructed with spacer thicknesses representing 20%, 30% and 50% compression against the wall of the custom trays on removal, impressions recorded, and casts fabricated in dental stone. Measurements for elastic recovery of irreversible hydrocolloid were done using an internal caliper and a digital caliper. All measurements were done by the principal investigator. Non-parametric analyses were used for comparisons of the undercut values between the 3D printed and poured casts to determine the amount of elastic recovery of the irreversible hydrocolloid impression material. There was no statistically significant difference in measurements between the original 3D printed casts and the poured casts, irrespective of percentage compression (p > 0.05). In removable partial denture construction, casts should be blocked out parallel to the path of insertion and then an additional 3mm of spacer applied as a standard technique before custom tray fabrication to ensure elastic recovery of the irreversible hydrocolloid impression. In severe undercut situations, accurate impressions can be taken using irreversible hydrocolloid by blocking out all undercut surfaces on the teeth and lingual sulci before adapting additional three-millimetre wax spacer on casts when constructing custom trays thereby ensuring accurate and reliable impressions for removable prosthesis construction.