The unpredictability of intermittent renewable energy (RE) sources (solar and wind) constitutes reliability challenges for utilities whose goal is to match electricity supply to consumer demands across centralized grid networks. Thus, balancing the variable and increasing power inputs from plants with intermittent energy sources becomes a fundamental issue for transmission system operators. As a result, forecasting techniques have obtained paramount importance. This work aims at exploiting the simplicity, fast computational and good generalization capability of Extreme Learning Machines (ELMs) in providing accurate 24 h-ahead solar photovoltaic (PV) power production predictions. The ELM architecture is firstly optimized, e.g., in terms of number of hidden neurons, and number of historical solar radiations and ambient temperatures (embedding dimension) required for training the ELM model, then it is used online to predict the solar PV power productions. The investigated ELM model is applied to a real case study of 264 kWp solar PV system installed on the roof of the Faculty of Engineering at the Applied Science Private University (ASU), Amman, Jordan. Results showed the capability of the ELM model in providing predictions that are slightly more accurate with negligible computational efforts compared to a Back Propagation Artificial Neural Network (BP-ANN) model, which is currently adopted by the PV system owners for the prediction task.
It has been shown that using fuel additives play an important role in enhancing the combustion characteristics in terms of efficiency and emissions. In addition, free piston engines have shown capable in reducing energy losses and presenting more efficient and reliable engines. In this context, the objective of the present work is to investigate the effect of using hydrogen as a fuel additive in natural gas homogeneous charge compression ignition free piston engine. To this aim, two models have been iteratively coupled: the combustion model that is used to calculate the heat release of the combustion and the scavenging model that is employed to determine the in-cylinder mixture state after scavenging in terms of its homogeneity and species mass fractions and to obtain the finial pressure and temperature of the in-cylinder mixture. In the former model, the 0-D approach through Cantera toolkit has been considered due to the fact that homogeneous charge compression ignition combustion is very rapid and the fuel-air mixture is well-homogenous, whereas in the latter model, 3-D-CFD approach through AN-SYS FLUENT software is considered to ensure precise calculations of the species exchange at the end of each engine cycle. The effect of hydrogen as a fuel additive has been quantified in terms of the combustion characteristics (e. g., ignition delay, heat release rate, engine overall efficiency and emissions, etc.). It has been shown that hydrogen addition reduces ignition delay time, decreases the in-cylinder peak pressure, while allowing the engine to operate with higher mechanical efficiency as it has high heat release rate, increases the NOx emission levels of the engine, but decreases the CO levels
This study presents a novel and interesting investigation regarding the use of exhaust gas recirculation (EGR) in free-piston engines by exploring EGR impact on both engine performance and emissions. A single-cylinder, two-stroke free-piston engine with an electrical generator model was investigated under the influence of EGR. A new dimethyl ether (DME) reaction mechanism was modified and used to simulate the DME combustion process under homogenous charge compression ignition conditions. The combustion process was described using the one-dimensional approach in which the in-cylinder gas mixture was treated as a single-zone reactor. Chemical kinetics approach was applied to calculate the combustion heat releasing rate and to include EGR effects. Many engine parameters were investigated by applying EGR in different ratios and in different temperatures. The results showed that EGR influences the combustion process by shifting the top dead center location toward the cylinder head, which yields higher compression ratio but shorter ignition delay. The engine ran with less generator power output when EGR was applied but with higher overall efficiency, meaning that the engine could convert more energy out of the combustion process at constant or low generator power demands. The study includes EGR impact on engine emissions in which both oxides of nitrogen ( ) and carbon monoxide (CO) emissions were investigated. Exhaust gas recirculation reduced the maximum bulk mean temperature of the gas mixture, which decreased the reaction rate of emissions. When running under stoichiometric conditions, EGR seemed to decrease CO emission by reducing the dissociation rate of carbon dioxide. Increasing the intake temperature by applying hot EGR affected both the engine power and emissions. A reduction in the engine efficiency and generator power output was observed as hot EGR was applied; additionally, high intake temperatures decreased EGR’s ability to reduce .
23 January 2019 in Advances in Mechanical Engineering
Forced convection of non-Newtonian Casson fluid laminar boundary layer flow past an isothermal horizontal flat plate in non-Darcy porous media is studied using Darcy–Forchheimer–Brinkman model. Similarity variables are used to transform the boundary layer equations. The boundary layer equations are reduced into system of first-order differential equations using similarity method. Then, solved numerically using adaptive Runge–Kutta–Fehlberg scheme simultaneously with shooting technique. The effects of Casson parameter, porosity, first- and second-order porous resistances, and Prandtl number on the fluid flow and heat transfer are investigated in terms of the local skin friction and local heat transfer parameters. In addition, velocity and temperature boundary layer profiles are plotted for all considered parameters. It is found that the heat transfer could be enhanced by increasing the Casson parameter and the porous resistance terms. To the contrary, the increase in the porosity reduces heat transfer rates. Finally, the increase in the Prandtl number enhances the heat transfer rates.
The aim of this work is to develop nonlinear low-dimensional models to describe vortex dynamics in spatially developing shear layers with periodicity in time. By allowing a free variable to dynamically describe downstream thickness spreading, we are able to obtain basis functions in a scaled reference frame and construct effective models with only a few modes in the new space. To apply this modified version of proper orthogonal decomposition (POD)/Galerkin projection, we first scale the flow along y dynamically to match a template function as it is developing downstream. In the scaled space, the first POD mode can capture more than 80% energy for each frequency. However, to construct a Galerkin model, the second POD mode plays a critical role and needs to be included. Finally, a reconstruction equation for the scaling variable g is derived to relate the scaled space to physical space, where downstream spreading of shear thickness occurs. Using only two POD modes at each frequency, our models capture the basic dynamics of shear layers, such as vortex roll-up (from a one-frequency model) and vortex-merging (from a two-frequency model). When arbitrary excitation at different harmonics is added to the model, we can clearly observe the promoting or delaying/eliminating vortex merging events as a result of mode competition, which is commonly demonstrated in experiments and numerical simulations of shear layers.