The characterization of materials, stress and fatigue state monitoring based on the acoustoelastic principle are gaining widespread attention in recent years, mainly due to their advantages such as high sensitivity and non-destructive character. This article presents the application of a non-destructive acoustic method to test the degree of degradation of materials with which the heating boiler is coated. The combustion chamber is covered in materials when the temperature of the process itself increases, and has a very positive effect on fuel combustion. Unfortunately, with the passage of time, such materials undergo gradation. This article describes an innovative measuring system that has been successfully applied to monitor changes in resonance frequency under uniaxial compression in refractory grade material, which by definition is characterized by a high level of heterogeneity with a network of pre-existing cracks. The paper indicates that both stress and elasticity coefficients have an impact on the vibration frequency of the measuring system. Initial research was conducted to qualitatively determine the influence of these parameters on the measured frequency of the system.
Corrosion is one of the most common wear mechanisms of refractories. Corrosive attacks lead to chemical and microstructural changes. Hot corrosion compromises chemical and/or physical interactions. Thus, the process is complex and not yet fully understood. Currently, corrosion is investigated post mortem by means of X-ray diffraction or scanning electron microscopy. These methods have the drawback that some information is lost on cooling. In-situ measurements, however, take measurements within the process. In resonant frequency and damping analysis (RFDA), a sample is excited to vibrate by a mechanical impulse. The vibrating sample emits an acoustic signal. This is recorded with a microphone and evaluated by means of Fast Fourier Transformation (FFT). We measured the change of the frequency of a low cement castable during the corrosion process. Further simplified experiments with less complex materials were done to confirm the results. Distinctive points of the curves could be correlated to specific corrosion phenomena, like melting or infiltration. The applied methods include a first characterization of the material with open porosity, density and in-situ high-temperature (HT)-RFDA measurements as well as a study of the slag behavior.
The incorporation of recycled metallurgical slags into refractory materials constitutes a promising approach to enhancing sustainability in the refractory industry. This study investigates the effect of vanadium-bearing slag aggregates as partial replacements for tabular alumina in castables and compares their behaviour with high-alumina and bauxite-based castables. Two vanadium-bearing slags with different mineralogical compositions were introduced in the 1–3 mm aggregate fraction with substitution up to 25 wt.%. Their effects on microstructure, thermo-mechanical performance, and corrosion resistance were evaluated. The introduction of vanadium-bearing slag significantly alters the microstructure of the castables, affecting their performance. Both slags displayed grains with higher porosity, microcracking, and heterogeneity compared with tabular alumina, but showed similarities to bauxite grains. Slag 1, enriched in calcium aluminate phases, provides limited mechanical strength but improved corrosion resistance due to improved bonding with the matrix. Slag 2, containing a higher spinel content, enhances mechanical strength, showing behaviour comparable with bauxite-based castables, particularly at 10 wt.% replacement. Vanadium is mainly present in metallic form and as Mg(Al,V)2O4 spinels in both slags. Upon firing, vanadium migrates toward the grain boundaries and reacts with the surrounding calcium aluminate phases to be incorporated in Ca(Al,V)2O4 and Ca(Al,V)4O7, while the spinel phase remains stable.
The incorporation of recycled metallurgical slags into refractory materials constitutes a promising approach to enhancing sustainability in the refractory industry. This study investigates the effect of vanadium-bearing slag aggregates as partial replace-ments for tabular alumina in castables and compares their behaviour with high-alumina and bauxite-based castables. Two vanadium-bearing slags with differ-ent mineralogical compositions were introduced in the 1-3 mm aggregate fraction with substitution up to 25 wt.%. Their effects on microstructure, thermo-mechanical performance and corrosion resistance were evaluated. The introduction of vanadi-um-bearing slag significantly alters the microstructure of the castables, affecting their performance. Both slags displayed grains with higher porosity, microcracking, and heterogeneity compared with tabular alumina, but show similarities with bauxite grains. Slag 1, enriched in calcium aluminate phases, provides limited mechanical strength but improved corrosion resistance due to improved bonding with the matrix. Slag 2, containing a higher spinel content, enhances mechanical strength, showing behaviour comparable to bauxite-based castables, particularly at 10 wt.% replacement. Vanadium is mainly present in metallic form and as Mg(Al,V)2O4 spinel in both slags. Upon firing, vanadium migrates toward grain boundaries and reacts with surround-ing calcium aluminate phases to be incorporated in Ca(Al,V)2O4 and Ca(Al,V)4O7, while the spinel phase remains stable.
The energy transition from the incineration and gasification of fossil fuels to the incineration and gasification of biomass refractory linings is being held up by a severe corrosion issue, caused by high alkali contents and the wide variety of biomass sources. Incinerators optimized for fossil fuels are commonly lined with mullite, Al2O3-Cr or SiC-based refractory products; however, those materials are not always suitable for the use of organic fuels. Hibonite (CaO·6Al2O3)-based refractory products have shown promising performance because of their high resistance against alkali attacks. Indeed, previous works have shown that the reaction between calcium hexa-aluminate and an alkali does not lead to the strong volume expansion observed with other mineral phases, such as corundum or andalusite. The present work aims to describe the reactions kinetics occurring between hibonite-based raw materials and biomass ashes. Therefore, the three main oxides contained in an average biomass, namely, CaO, SiO2 and K2O, were selected to examine the high temperature reactions with a calcium hexa-aluminate matrix. The resulting phase composition and microstructure were compared with the performance of an alumina matrix through, respectively, X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM). The post-mortem observations show a higher extent of reaction for the alumina than for the calcium hexa-aluminate. Moreover, the microstructure of the alumina matrix suffered a strong chemical spalling, while the calcium hexa-aluminate microstructure remained undamaged after the corrosion.