This paper presents a compact, low-cost unmanned aerial system for antenna measurement. The proposed system overcomes existing limitations in terms of unmanned aerial vehicle positioning and data geo-referring accuracy using a real-time kinematic positioning system to achieve centimeter-level accuracy. Amplitude-only measurements acquired using a low-cost power sensor are processed by means of the phaseless sources reconstruction method. This is an iterative phase retrieval technique that allows recovering an equivalent currents distribution, which characterizes the antenna under test (AUT). From these equivalent currents, near-field to far-field transformation is applied to calculate the AUT radiation pattern. This contribution also analyzes probe antenna characterization and the impact of positioning and geo-referring accuracy on the radiation pattern. Two application examples of antenna measurement at S- and C-bands using the implemented system are presented.
21 September 2017 in IEEE Transactions on Antennas and Propagation
In this paper, we propose a ball grid array (BGA) module with an integrated 3-D-printed plastic lens antenna for application in a dedicated 130 GHz OOK transceiver that targets the area of 5G backhaul/fronthaul systems. The main design goal was the full integration of a small footprint antenna with an energy-efficient transceiver. The antenna system must be compact and cost effective while delivering an approximately 30 dBi gain in the working band, defined as 120 to 140 GHz. Accordingly, a $2 \times 2$ array of aperture-coupled patch antennas was designed in the $7 \times 7 \times 0.362$ mm3 BGA module as the feed antenna of the lens. This achieved a 7.8 dBi realized gain, broadside polarization purity above 20 dB, and over 55% total efficiency from 110 to 140 GHz (20% bandwidth). A plastic elliptical lens 40 mm in diameter and 42.3 mm in height was placed on top of the BGA module. The antenna achieved a return loss better than −10 dB and a 28 dBi realized gain from 114 to 140 GHz. Finally, active measurements demonstrated a >12 Gbps Tx/Rx link at 5 m with bit error rate (BER) < 10−6 at 1.6 pJ/b/m. These results pave the way for future cost-effective, energy-efficient, high-data rate backhaul/fronthaul systems for 5G communications.
9 March 2016 in IEEE Transactions on Antennas and Propagation
This paper presents a novel interrogation system that combines multiple millimeter wave transmitters and receivers to create real-time high-resolution radar images for personnel security screening. The main novelty of the presented system is that the images can be created as the person being screened continuously moves across a corridor where the transmitters and receivers, working in a fully coherent architecture, are distributed. As the person moves, the transmitters and receivers are sequentially activated to collect data from different angles to inspect the whole body. Multiple images, similar to video frames, are created and examined to look for possible anomalies such as concealed threats. Two-dimensional (2-D) and three-dimensional (3-D) setups have been simulated to show the feasibility of the proposed system. The simulation results in 2-D have been validated using measurements.
5 December 2014 in IEEE Transactions on Antennas and Propagation
This paper presents a broadband and phaseless synthetic aperture radar (SAR) with efficient sampling. The design relies on a novel phaseless monostatic element comprising a transmitter and a receiver. This element, together with a computationally inexpensive algorithm, can retrieve the phase of the monostatic scattered field at all the working band except for two small safety margins at the lower and upper frequencies. Furthermore, the phase retrieval works independently of the transmitter/receiver position. Consequently, conventional approaches to reduce the number of monostatic acquisition points can be employed. Thus, the proposed strategy is suitable to implement either arrays that benefit from a reduced number of low-complexity elements or raster scan systems that benefit not only from the cost reduction of the scanning components but also from a remarkable speed-up due to the reduced number of acquisition points. Moreover, in contrast to other off-axis schemes, the proposed system does not require neither mechanical nor electrical phase shifting and, therefore, it can be directly adapted to a large number of frequency bands. The performance of the system is validated by simulation and measurement examples in the millimeter-wave band.
30 July 2013 in IEEE Transactions on Antennas and Propagation
A new submillimeter-wave imaging system based on the frequency scanning concept is presented. Using significantly less information than beam-steering techniques, frequency scanning-based imaging systems are able to provide angular information in range-based radar systems which do not allow mechanical or electronic beam steering. Several strategies have been adopted to overcome the low dynamic range due to the propagation losses and non-specular reflection on the object-under-test. Moreover, the system is not only capable of detecting the placement of the objects, but also their profile. In this sense, an imaging application showing the system capabilities for the detection of objects concealed under clothes is presented. Results using 1-D FSAA allowing profile imaging are shown, proving the validity of the proposed system.
1 July 2014 in IET Microwaves, Antennas & Propagation
An optimisation framework for near field multifocusing on antenna arrays is proposed. Its aim is to obtain the feeding weights that must be applied to the elements of the array so that the antenna focuses on two or more targets simultaneously. The method is based on the definition of a proper cost function, which is minimised using an optimisation algorithm over an equivalent least squares problem. The success of the technique is noted in the fact that different array parameters can be obtained: magnitude and phase of the array elements or only phase synthesis. In order to show the efficiency of the method, several tests are carried out using different arrays and optimisation parameters. The simulation, manufacture and measurement of an 8 × 8 planar array able to focus on two different targets is also performed. Results show how the framework can be applied to general arrays and demanding requirements, so it may be easily extended to different synthesis problems besides multifocusing.