A new type of rigid-flexible coupling three degrees of freedom (3-DOF) micro-positioning platform with high positioning accuracy and high bearing capacity is developed, which consists of flexible drive mechanism and rigid platform. The flexible drive mechanism consists of three sets of symmetrical parallel round flexible hinge structures, each with a wedge structure in the middle of the symmetrical parallel flexible hinge. The rigid platform has an inclined plane with the same angle as the wedge, while the wedge structure is used to achieve the self-locking effect. The flexibility matrix method and ANSYS are used to analyze the statics of the flexible drive mechanism. The first four natural frequencies of the platform are obtained by dynamic simulation analysis. A symmetrical rigid flexible coupling micro-positioning platform experimental system is developed. Output characteristics, positioning accuracy, relationship between frequency and amplitude, and bearing performance of the micro-positioning platform are tested. These experimental results obviously show that the micro-positioning platform has good motion characteristics, high positioning accuracy, large movement distance, and large load bearing capacity performance.
This paper describes the innovative design of a three-dimensional (3D) motion device based on a flexible mechanism, which is used primarily to produce accurate and fast micro-displacement. For example, the rapid contact and separation of the tool and the workpiece are realized by the operation of the 3D motion device in the machining process. This paper mainly concerns the device performance. A theoretical model for the static performance of the device was established using the matrix-based compliance modeling (MCM) method, and the static characteristics of the device were numerically simulated by finite element analysis (FEA). The Lagrangian principle and the finite element analysis method for device dynamics are used for prediction to obtain the natural frequency of the device. Under no-load conditions, the dynamic response performance and linear motion performance of the three directions were tested and analyzed with different input signals, and three sets of vibration trajectories were obtained. Finally, the scratching experiment was carried out. The detection of the workpiece reveals a pronounced periodic texture on the surface, which verifies that the vibration device can generate an ideal 3D vibration trajectory.
A molecular dynamics model of the diamond abrasive polishing the single crystal silicon is established. Crystal surfaces of the single crystal silicon in the Y-direction are (010), (011), and (111) surfaces, respectively. The effects of crystallographic orientations on polishing the non-continuous single crystal silicon surfaces are discussed from the aspects of surface morphology, displacement, polishing force, and phase transformation. The simulation results show that the Si(010) surface accumulates chips more easily than Si(011) and Si(111) surfaces. Si(010) and Si(011) workpieces are deformed in the entire pore walls on the entry areas of pores, while the Si(111) workpiece is a local large deformation on entry areas of the pores. Comparing the recovery value of the displacement in different workpieces, it can be seen that the elastic deformation of the A side in the Si(011) workpiece is larger than that of the A side in other workpieces. Pores cause the tangential force and normal force to fluctuate. The fluctuation range of the tangential force is small, and the fluctuation range of the normal force is large. Crystallographic orientations mainly affect the position where the tangential force reaches the maximum and minimum values and the magnitude of the decrease in the tangential force near the pores. The position of the normal force reaching the maximum and minimum values near the pores is basically the same, and different crystallographic orientations have no obvious effect on the drop of the normal force, except for a slight fluctuation in the value. The high-pressure phase transformation is the main way to change the crystal structure. The Si(111) surface is the cleavage surface of single crystal silicon, and the total number of main phase transformation atoms on the Si(111) surface is the largest among the three types of workpieces. In addition, the phase transformation in Si(010) and Si(011) workpieces extends to the bottom of pores, and the Si(111) workpiece does not extend to the bottom of pores.
Two-dimensional vibration-assisted polishing (2D-VAP) is a new polishing approach proposed in recent years, which is considered to be very suitable for the polishing of micro-optical parts and micro-structured surfaces. The advantages of the 2D-VAP approach are as follows: A very high relative velocity can be obtained between the workpiece and the polishing tool; the desired motion trajectory can be formed in one polishing cycle. However, there are still some problems to be solved in the 2D-VAP approach, mainly involving: The vibration frequency of the resonant excitation cannot be regulated, which makes it difficult to adapt to the processing demands of different materials; the theoretical model of removal function has been studied in few papers; and motion coupling occurs easily between the horizontal and vertical directions, which affects the trajectory synthesized at the polishing tool. In order to solve these problems, a new approach to decoupled non-resonant polishing is developed in this paper, and its effectiveness is investigated by the theoretical analysis and polishing experiments. Theoretical studies of removal function show that the vibration frequency, vibration amplitude and loading force are proportional to the removal depth. The comparison of experimental and modeling results of removal function show that they have good coherence, and the correctness of the theoretical model of removal function is verified. In addition, the stability experiments of removal function prove that the polishing approach has better stability and is beneficial to the convergence of workpiece surface.
Flexure-based micropositioning stages with high positioning precision are really attractive. This paper reports the design and analysis processes of a two-degree-of-freedom (2-DOF) flexure-based XY micropositioning stage driven by piezoelectric actuators to improve the positioning accuracy and motion performance. First, the structure of the stage was proposed, which was based on rectangular flexure hinges and piezoelectric actuators (PZT) that were arranged symmetrically to realize XY motion. Then, analytical models describing the output stiffness in the XY directions of the stage were established using the compliance matrix method. The finite element analysis method (FEA) was used to validate the analytical models and analyze the static characteristics and the natural frequency of the stage simultaneously. Furthermore, a prototype of the micropositioning stage was fabricated for the performance tests. The output response performance of the stage without an end load was tested using different input signals. The results indicated that the stage had a single direction amplification capability, low hysteresis, and a wide positioning space. The conclusion was that the proposed stage possessed an ideal positioning property and could be well applied to the positioning system.