Li Liu

Dr. Li Liu

none

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 November 2020 in Micromachines
Verified
Journal Article
Open access
PDF file
GWGuilian Wang
Guilian Wang
YWYong Wang
Yong Wang
BLBingrui Lv
Bingrui Lv
RMRuopeng Ma
Ruopeng Ma
LLLi Liu
Li Liu
A new type of rigid-flexible coupling three degrees of freedom (3-DOF) micro-positioning platform with high positioning accuracy and high bearing capacity is developed, which consists of flexible drive mechanism and rigid platform. The flexible drive mechanism consists of three sets of symmetrical parallel round flexible hinge structures, each with a wedge structure in the middle of the symmetrical parallel flexible hinge. The rigid platform has an inclined plane with the same angle as the wedge, while the wedge structure is used to achieve the self-locking effect. The flexibility matrix method and ANSYS are used to analyze the statics of the flexible drive mechanism. The first four natural frequencies of the platform are obtained by dynamic simulation analysis. A symmetrical rigid flexible coupling micro-positioning platform experimental system is developed. Output characteristics, positioning accuracy, relationship between frequency and amplitude, and bearing performance of the micro-positioning platform are tested. These experimental results obviously show that the micro-positioning platform has good motion characteristics, high positioning accuracy, large movement distance, and large load bearing capacity performance.

23 March 2020 in Integrated Ferroelectrics
Verified
Journal Article
Closed access
LLLi Liu
Li Liu
MWMingyang Wu
Mingyang Wu
LLLubin Li
Lubin Li
YCYaonan Cheng
Yaonan Cheng
High-pressure jet coolant assistance was used in the cutting process of Inconel 718. The effects of coolant pressure on cutting force and machined surface quality were researched. As well as the experimental design, Two-dimensional cutting models for Inconel 718 were established using AdvantEdge FEM software. Simulations and experiments were carried out based on the Taguchi method. The simulation predictions and experimental test results were compared. The influence of variables on cutting force and machined surface roughness was determined by variance analysis. The effect of cooling pressure on roughness of machined surfaces was studied by simulation and experiment tests.

26 April 2015 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
YCYaonan Cheng
Yaonan Cheng
LLLi Liu
Li Liu
ZLZhenzhen Lu
Zhenzhen Lu
RGRui Guan
Rui Guan
TWTong Wang
Tong Wang

13 June 2021 in Integrated Ferroelectrics
Verified
Journal Article
Closed access
LLLi Liu
Li Liu
GWGuilian Wang
Guilian Wang
JLJie Liu
Jie Liu
YCYaonan Cheng
Yaonan Cheng
In the milling process of water chamber head, the service life of cemented carbide inserts is low, and inserts are prone to premature breakage and impact fracture. Dynamic cutting force is one of the main factors leading to insert failure. In this paper, a dynamic cutting force model is established based on the characteristics of asymmetric milling of water chamber head and the characterization of cutting area variables. By comparing the calculated value with the experimental value, the model can describe the change of dynamic cutting force. Through theoretical analysis and insert stress distribution simulation, it is found that under the impact load of cutting force, the radial tension stress between the compression zone and the stretching zone is the main reason for the insert to crack and break. The results of this paper provide reference for the study of carbide insert failure.

13 June 2021 in Integrated Ferroelectrics
Verified
Journal Article
Closed access
LLLi Liu
Li Liu
JLJie Liu
Jie Liu
GWGuilian Wang
Guilian Wang
YCYaonan Cheng
Yaonan Cheng
The coating on carbide insert surface can effectively reduce the transfer of cutting heat to the inside of the insert, improve the surface wear resistance and cutting performance, and ensure the service life. In this paper, the influence of coating on the heat conduction inside the insert is analyzed by two-dimensional heat transfer model, and the temperature distribution is quantitatively described. The simulation models of TiAlN-coated and -uncoated inserts are established, and the simulation results are compared. It is found that the cutting temperature of TiAlN-coated insert decreased by about 5% compared with that of uncoated cutting tools. The coating effectively reduced the conduction of cutting heat to the matrix, and the internal temperature of the matrix was significantly lower than that of uncoated cutting tools.

14 February 2015 in Chinese Journal of Mechanical Engineering
Verified
Journal Article
Closed access
PDF file
XLXianli Liu
Xianli Liu
GHGenghuang He
Genghuang He
FYFugang Yan
Fugang Yan
YCYaonan Cheng
Yaonan Cheng
LLLi Liu
Li Liu
There has existed a great deal of theory researches in term of chip production and chip breaking characteristics under conventional cutting and high speed cutting conditions, however, there isn’t sufficient research on chip formation mechanism as well as its influence on cutting state regarding large workpieces under extreme load cutting. This paper presents a model of large saw-tooth chip through applying finite element simulation method, which gives a profound analysis about the characteristics of the extreme load cutting as well as morphology and removal of the large chip. In the meantime, a calculation formula that gives a quantitative description of the saw-tooth level regarding the large chip is established on the basis of cutting experiments on high temperature and high strength steel 2.25Cr-1Mo-0.25V. The cutting experiments are carried out by using the scanning electron microscope and super depth of field electron microscope to measure and calculate the large chip produced under different cutting parameters, which can verify the validity of the established model. The calculating results show that the large saw-toothed chip is produced under the squeezing action between workpiece and cutting tools. In the meanwhile, the chip develops a hardened layer where contacts the cutting tool and the saw-tooth of the chip tend to form in transverse direction. This research creates the theoretical model for large chip and performs the cutting experiments under the extreme load cutting condition, as well as analyzes the production mechanism of the large chip in the macro and micro conditions. Therefore, the proposed research could provide theoretical guidance and technical support in improving productivity and cutting technology research.