Galiya Akhmedyanova

Dr. Galiya Akhmedyanova

orcid

Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
Verified
Journal Article
Open access
PDF file
BRBoranbay Ratov
Boranbay Ratov
VMVolodymyr A. Mechnik
Volodymyr A. Mechnik
Edwin Spartak GevorkyanEdwin Spartak Gevorkyan
Edwin Spartak Gevorkyan
Miroslaw RuckiMiroslaw Rucki
Miroslaw Rucki
DPDaniel Pieniak
Daniel Pieniak
АААнар Абилаханова
Анар Абилаханова
To produce strong and wear-resistant tools for the rock drilling industry, the most commonly used metal matrix composites contain the reinforcing phase of cemented carbide. There are numerous research reports on attempts to improve the performance of WC-Co composites. The paper is a continuation of previously reported research on the SPS-processed WC–6 wt.%Co metal matrix composites with yttria-stabilized zirconia (YSZ) addition in amounts of 4 wt.% and 10 wt.%. The sintered specimens were polished and underwent the microindentation tests with a Vickers shape diamond tip. The following parameters were measured: stiffness S, the Poisson number ν, indentation creep CIT, relaxation RIT, indentation hardness HIT, indentation Vickers hardness HVIT, Martens hardness HM, reduced modulus E*, and indentation elastic modulus EIT. The tests revealed hardness values of 16.2–17.0 GPa and indentation elastic moduli in the range of 607–670 GPa. Moreover, respective plastic and elastic parts of the indentation work Wplast and Welast were determined. It was found that YSZ addition slightly reduced hardness and modulus, but all the three wear parameters, H/E, H3/E2, and 1/(E2H), increased after addition of zirconia. Specifically, for 10 wt.% ZrO2 H/E increased by 5%, H3/E2 by 7%, while 1/(E2H) by 27% compared to 94WC–6Co composition.

1 July 2026 in Material and Mechanical Engineering Technology
Verified
Journal Article
Closed access
AMAdilbek Mustafin
Adilbek Mustafin
NSNursultan Sadykov
Nursultan Sadykov
GAGulnara Abdullina
Gulnara Abdullina
GAGaliya Akhmedyanova
Galiya Akhmedyanova
DADinara Aigozhina
Dinara Aigozhina
The dynamics of the vibration process of a pumping unit can be considered as independent oscillations of two separate sprung masses from the centrifugal force: the rotor on the bearings and the pump casing on the foundation supports. In the absence of special damping devices in the oscillating system, the reaction force from the rotor vibration affects the casing and the bearing supports approximately equally. However, when dampers are used in the oscillating system, they can significantly reduce transmitted force to unit supports. Such a method made it possible, in addition to the acoustic parameters of the unit, to determine the dynamic loads on the supports and to conduct a comparative assessment of the strength parameters of rolling bearings. Vibration protection of rotating machines, i. e. with a rotor, which includes an impeller with a shaft and support parts, requires a large amount of research, largely experimental in nature. At present, some of this work can be significantly reduced by using mathematical apparatus to perform calculations and model dynamic processes. The aim of the paper is to show method and model to calculate dynamics of vibration process in a pumping unit, considering elastic and dissipative properties of elements in support devices.

7 June 2026 in Materials
Verified
Journal Article
Open access
PDF file
BRBoranbay Ratov
Boranbay Ratov
VMVolodymyr A. Mechnik
Volodymyr A. Mechnik
Edwin Spartak GevorkyanEdwin Spartak Gevorkyan
Edwin Spartak Gevorkyan
Miroslaw RuckiMiroslaw Rucki
Miroslaw Rucki
DPDaniel Pieniak
Daniel Pieniak
GAGaliya Akhmedyanova
Galiya Akhmedyanova
WC–Co composites are widely applied in various industries due to their high hardness and wear resistance. The addition of zirconia further enhanced the composite, improving grain refinement and reducing the friction coefficient. Zirconia submicron particulate reinforcement strengthened the cobalt binder phase, significantly improving the wear resistance. Tribological tests were performed in ball-on-flat dry sliding mode, against an Al2O3 counter body. The specimen WC–6Co–10ZrO2 exhibited a decrease in volumetric loss ΔV by 66% compared to 94WC–6Co composite, and the wear rates Ws showed a 50% decrease for 4 wt.% zirconia addition and up to 80% when 10 wt.% ZrO2 was added. In tribological tests, a five times larger load, 100 N instead of 20 N, caused an increase in the wear rate 1.1, 1.3, and 1.9 times for WC–Co, WC–6Co–4ZrO2, and WC–6Co–10ZrO2 compositions, respectively. Abrasive and adhesive wear mechanisms were identified.

30 October 2026 in Neft i Gaz
Verified
Journal Article
Closed access
GAGaliya Akhmedyanova
Galiya Akhmedyanova
AKAidar Ermekkalievish Kuttybayev
Aidar Ermekkalievish Kuttybayev
GAG.G. Abdullina
G.G. Abdullina
DAD.G. Aigozhina
D.G. Aigozhina
МAМ.M. Aliakbar
М.M. Aliakbar
ZKZh.M. Kenzhegaliyeva
Zh.M. Kenzhegaliyeva
This paper presents a systematic review of modern rock-cutting tools used in rotary drilling of oil and gas wells. Roller-cone, PDC, and diamond-impregnated bits, as well as combined designs, are considered. The main rock-breaking mechanisms and the effects of weight on bit, rotational speed, depth of cut, rock properties, bottomhole pressure, temperature, hydraulic conditions, and cutter wear are analyzed. Mechanical specific energy (MSE) is considered together with rate of penetration, load, rotational speed, torque, and bit condition as a set of performance indicators. The comparative analysis shows that PDC bits have high potential rate of penetration and energy efficiency in suitable intervals, roller-cone bits provide resistance to impact loading and a broad range of applications, while diamondimpregnated bits provide high wear resistance in hard and abrasive formations. The results demonstrate that bit effectiveness depends on matching bit design to specific geological and technical conditions. The practical significance of the study is the systematization of criteria for preliminary bit selection and operating-mode optimization with regard to productivity, energy efficiency, reliability, hydraulic conditions, and economic factors. Prospects for digital wear monitoring and machine-learning methods for PDC cutter condition assessment and tool optimization are also identified.