Peng Wang

Mr. Peng Wang


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 July 2018 in Materials
Verified
Journal Article
Open access
PDF file
Wentian ShiWentian Shi
Wentian Shi
YLYude Liu
Yude Liu
XSXuezhi Shi
Xuezhi Shi
YHYanjun Hou
Yanjun Hou
PWPeng Wang
Peng Wang
GSGuohua Song
Guohua Song
A 400 W high-power laser was used to fabricate 200-µm-thick Ti-6Al-4V samples to evaluate the effects of small (50 μm) and large (200 μm) beam diameter on density, microstructure and mechanical properties. A series of single-track experiments demonstrated that it was challenging for the small-beam laser to fabricate smooth and defect-free scan tracks. A larger beam diameter efficiently avoided process instability and provided a more stable and uniform melt pool. By increasing the beam diameter, the density of multilayer samples reached 99.95% of the theoretical value, which is much higher than that achieved with the small beam diameter. However, it was difficult to completely eliminate defects due to serious spatter and evaporation. Moreover, all of the generated samples had relatively coarse surfaces. For the large beam diameter of 200 µm, the optimal yield strength, ultimate tensile strength and elongation were 1150 MPa, 1200 MPa and 8.02%, respectively. In comparison, the small beam diameter of 50 µm resulted in values of 1035 MPa, 1100 MPa and 5.91%, respectively. Overall, the large-diameter laser is more suitable for high-power selective laser melting (SLM) technology, especially for thick layers.

27 March 2019 in Metals
Verified
Journal Article
Open access
PDF file
Wentian ShiWentian Shi
Wentian Shi
PWPeng Wang
Peng Wang
YLYude Liu
Yude Liu
GHGuoliang Han
Guoliang Han
To improve the precision of the nonhorizontal suspension structure and the forming quality of the overhanging surface by selective laser melting, the influence of laser power on the upper surface and the overhanging surface forming quality of 316L stainless steel at different forming angles was studied in the experiment. The influence of different scanning strategies, upper surface remelting optimization, and overhang boundary scanning optimization on the formation of overhanging structures was compared and analyzed. The forming effect of chromium–nickel alloy is better than 316L stainless steel below the limit forming angle in the overhanging structure. The better forming effect of chromium–nickel alloy can be obtained by narrowing the hatch space with the boundary optimization process. The experiment results show that the forming of the overhanging structure below the limit forming angle should adopt the chessboard scanning strategy. The smaller laser power remelting is beneficial to both the forming of the overhanging surface and the quality of upper surface forming. The minimum value of surface roughness using the 110 W power laser twice during surface remelting and boundary scanning 75° overhanging surface can reach 11.9 μm and 31.1 μm, respectively. The forming accuracy error range above the limit forming angle is controlled within 0.4 mm, and the forming quality is better. A boundary count scanning strategy was applied to this study to obtain lower overhanging surface roughness values. This research proposes a process optimization and improvement method for the nonhorizontal suspension structure formed by selective laser melting, which provides the process support for practical application.

29 October 2021 in Coatings
Verified
Journal Article
Open access
PDF file
YJYan-Long Jing
Yan-Long Jing
PWPeng Wang
Peng Wang
XYXiaoling Yan
Xiaoling Yan
To improve the quality of thick powder bed and realize the matching of thick powder bed and thin powder bed in the later stage, the influence of process parameters for the single-track, multi-layer fabrication, relative density, surface quality, defect, remelting, and boundary optimization performance of different layer thicknesses of Ti-6Al-4V fabricated by selective laser melting were investigated. It is more conducive to the stable forming of single-track when the point distance is half the diameter of the laser beam, and the exposure time is appropriately extended. The thin powder bed needs the corresponding point distance and exposure time under the laser power of 280–380 W to obtain high-density specimens. The thick powder bed needs to be able to ensure the formation of high-quality specimens under the smaller point distance and longer exposure time under higher laser power of 380 W. Both thick powder bed and thin powder bed will cause un-melted defects between molten pools, spheroidization defects caused by splashing, and microporous defects. The remelting process can significantly improve the surface quality of the formed specimen, but the surface quality of the thick powder bed is worse than that of the thin powder bed. The boundary quality of thick powder bed is worse than that of thin powder bed, and the boundary shape has a greater influence on the quality of the SLM forming boundary. Different strategies should be adopted to form the boundary of different shapes. Increasing the boundary count and increasing the laser power are more conducive to the improvement of boundary quality.