Nazimuddin M. Wasiuddin

Prof. Nazimuddin M. Wasiuddin

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 June 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
IBRAHIM ELNAMLIBRAHIM ELNAML
IBRAHIM ELNAML
JLJun Liu
Jun Liu
LMLouay N Mohammad
Louay N Mohammad
NWNazimuddin M. Wasiuddin
Nazimuddin M. Wasiuddin
SCSamuel B. Cooper
Samuel B. Cooper
SCSamuel B. Cooper
Samuel B. Cooper
There is growing interest in sustainable road pavement technologies to protect the environment and provide economic benefits. Post-consumer recycled (PCR) plastics are considered for construction to address the threat of plastic waste materials (PWM) and to improve sustainability. Asphalt pavement construction is highly considered for PWM recycling due to its large daily production. The purpose of this study is to investigate the performance of asphalt mixture containing PWM, specifically high-density polyethylene (HDPE), and compare its performance with two conventional mixtures. Three asphalt mixtures were considered: (1) mixture with asphalt binder PG 76-22 (SBS-modified); (2) mixture with asphalt binder PG 70-22 (SBS-modified); and (3) mixture with binder PG 67-22 and 3% HDPE (the plastic mixture). The rheological properties of the modified asphalt binders and the performance of the modified asphalt mixtures were evaluated. The long-term field performance of the pavements was modeled using AASHTOWare software (v.1.1.6) for the three mixtures considered. The results showed that all the mixtures were able to comply with the cracking threshold specified by the Louisiana Department of Transportation and Development (LaDOTD) for high-traffic volume roads. In addition, the plastic asphalt mixture showed similar performance to the one containing PG 70-22 (SBS-modified) asphalt binder.

4 June 2019 in Transportation Research Record: Journal of the Transportation Research Board
Verified
Journal Article
Closed access
PDF file
RHRoksana Hossain
Roksana Hossain
NWNazimuddin M. Wasiuddin
Nazimuddin M. Wasiuddin
Styrene-butadiene-styrene (SBS) modified PG 64-22 and PG 76-22 binders are studied to investigate the degradation of polymer because of aging applied by: rolling thin film oven (RTFO), pressure aging vessel (PAV), and ultraviolet (UV). Upon observing the temperature increment of unmodified binder during high shear mixing, a polymer mixing procedure has been established. SBS (2%, 4%, and 6%), polyphosphoric acid (PPA) (0.5%, 2%, and 3.5%), and PPA (2%)-SBS (0.5%, 2%, and 3.5%) are mixed with PG 64-22 binder. Sentmanat extensional rheometer, based on dynamic shear rheometer, is used to investigate the extensional deformation characteristics in which SBS modified binders exhibit both first peak elongation force, F1, and second peak elongation force, F2, whereas, unmodified binders and PPA modified binders exhibit no F2. SBS is the most effective in increasing F2 with an increasing rate of 1.16N/% of SBS polymer. At 12°C and 16°C, F2 of RTFO aged SBS modified binder reduces, which indicates the polymer is degrading. In the case of PAV aged SBS modified binder, no F2 is found at 12°C and 16°C. With the increment of temperature, the PAV aged sample shows F2, but the value is less than the F2 of the original and RTFO aged binder of similar stiffness (F1). A normalized parameter, F2/F1, also shows that RTFO and PAV aging degrade SBS. Evaluation of UV aged SBS modified binder shows no F2 at any temperature while oven aged binder shows F2 value at similar aging temperature, duration, and thickness, indicating SBS completely degrades because of UV aging.

1 March 2013 in Journal of Testing and Evaluation
Verified
Journal Article
Closed access
NWNazimuddin M. Wasiuddin
Nazimuddin M. Wasiuddin
AMAmanda Marshall
Amanda Marshall
NSNibert E. Saltibus
Nibert E. Saltibus
ASAziz Saber
Aziz Saber
CAChristopher Abadie
Christopher Abadie
LMLouay N Mohammad
Louay N Mohammad
Currently, the scope of the standard test method for sweep test of bituminous emulsion surface treatment samples (ASTM D7000) is limited to emulsion-based chip seals only. To this end, the objective of this study is to evaluate the sensitivity of the sweep test for both emulsions and hot asphalts, with respect to aggregate mineralogical types, aggregate precoating, aggregate moisture content, asphaltic materials type, and application rates of asphaltic materials. For the field evaluation, fifteen chip seal test sections were prepared with three asphaltic materials and five aggregates in a 9-acre parking lot. Two years after construction, each of the 15 sections were visually inspected for aggregate loss and bleeding. Each section was given a distress rating. The % aggregate loss from the sweep test was then compared with the field distress rating. Both laboratory and field tests indicate that overall, expanded shale lightweight aggregate is better than any crushed stone, whereas clay lightweight performed the worst among the six aggregates tested in this study. Precoated expanded shale lightweight aggregates performed better than uncoated shale lightweight aggregates, with respect to % aggregate loss. Between the two hot asphalts, PAC-15 performed better than AC20-5TR. In the case of hot asphalt, the % aggregate loss increases as moisture content increases in oven dry, air dry, and saturated surface dry aggregates. However, for emulsion, air dry aggregates performed the best. For both emulsion and hot asphalt, an increase in asphaltic materials application rate reduces the % aggregate loss significantly. Distress rankings in all 15 sections, except for one PAC-15 section, matched sweep test rankings. Overall, the results indicate that the sweep test using both emulsion and hot asphalt can be an effective tool for evaluation of performance of chip seals.

15 April 2025 in Construction and Building Materials
Verified
Journal Article
Closed access
SSShahjalal Selim
Shahjalal Selim
RIReazul Islam
Reazul Islam
NWNazimuddin M. Wasiuddin
Nazimuddin M. Wasiuddin
APAndrew Peters
Andrew Peters

1 May 2016 in Journal of Materials in Civil Engineering
Verified
Journal Article
Closed access
RIReadul Mohammad Islam
Readul Mohammad Islam
WKWilliam “Bill” King
William “Bill” King
NWNazimuddin M. Wasiuddin
Nazimuddin M. Wasiuddin
Two most common distresses found in chip seals are raveling and bleeding. Although raveling is a process that continues throughout the whole service life of chip seals, current performance tests available for chip seals focus mainly on early raveling and bond maturation. In this study, chip seals binders from the field were extracted and recovered for two consecutive years. Rheological properties of original, field-aged, and laboratory-aged binders were compared. Results showed that pressurized aging vessel (PAV-) aging simulates 3 to 4 years of field-aging for hot asphalt and less than 3 years for emulsion. Strain tolerance, shear stress at failure, oxidative aging index, and yield energy of the binder were correlated with long term field performance (raveling). Shear stress at failure of field-aged binders showed strong correlation with long-term field performance, exhibiting an R2 value of 0.95. However, yield energy (a product of strain tolerance and shear stress at failure) of original binder...

11 March 2011
Verified
Conference Paper
Closed access
NWNazimuddin M. Wasiuddin
Nazimuddin M. Wasiuddin
NSN. Saltibus
N. Saltibus
LMLouay N Mohammad
Louay N Mohammad
Despite the positive effects, the use of wax-based warm mix additive is very limited due to the concerns on cohesion and adhesion properties. The objective of this study is to evaluate the cohesive strengths of asphalt binders with and without Sasobit®, a wax-based warm mix additive using a pneumatic adhesion tensile testing instrument (PATTI) and using surface free energy method from optical advancing contact angle measurements. Two asphalt binders, PG 64-22 and PG 76-22M with and without 2% Sasobit® were coated in 2"X2"X1/4" glass plates. Cohesive strengths of asphalt binders were obtained in terms of pull-off tensile strength (POTS) using ½ in diameter pull-stubs. It was observed that the cohesive strengths of PG64-22 and PG76-22M are 1.964 MPa (284.9±21.3 psi) and 2.067 MPa (299.9±15.3 psi), respectively. Sasobit® reduced the cohesive strengths to 1.468 MPa (212.9±11.3 psi) and 1.503 MPa (218.0±17.7 psi), respectively for PG 64-22 and PG 76-22M. The cohesive strengths (free energy of cohesion) obtained from surface free energy measurements indicate that PG 64-22 has higher cohesive strengths and Sasobit® increases the cohesive strengths of both the binders. Overall, pull-off test was found to be simple and reproducible.