In the exploration of sustainable construction materials, the application of ferronickel slag (FNS) in creating pervious concrete has been investigated, considering its potential to meet the dual requirements of mechanical strength and fluid permeability. To elucidate the statistical properties and models for predicting the performance of FNS-composited pervious concrete with different sizes of aggregates and mixtures, a series of experiments, including 54 kinds of mixtures and three kinds of aggregate, were conducted. The focus was on measuring the compressive strength and the permeability coefficient. The results indicate that the compressive strength of pervious concrete decreases with the increase in aggregate size, while the permeability coefficient increases with the increase in aggregate size. Through normalization, the variability of these properties was quantitatively analyzed, revealing coefficients of variation for the concrete’s overall compressive strength and the permeability coefficient at 0.166, 0.132, and 0.150, respectively. Predictive models were developed using machine learning techniques, such as Linear Regression, Support Vector Machines, Regression Trees, and Gaussian Process Regression. These models demonstrated proficiency in forecasting the concrete’s compressive strength and permeability coefficient.
Impact tests on post-fire concrete confined by Carbon Fiber-Reinforced Polymer/Plastic (CFRP) sheets were carried out by using Split Hopkinson Pressure Bar (SHPB) experimental setup in this paper, with emphasis on the effect of exposed temperatures, CFRP layers and impact velocities. Firstly, according to the measured stress-strain curves, the effects of experiment parameters on concrete dynamic mechanical performance such as compressive strength, ultimate strain and energy absorption are discussed in details. Additionally, temperature caused a softening effect on the compressive strength of concrete specimens, while CFRP confinement and strain rate play a hardening effect, which can lead to the increase in dynamic compressive strength by 1.8 to 3.6 times compared to static conditions. However, their hardening mechanisms and action stages are extremely different. Finally, nine widely accepted Dynamic Increase Factor (DIF) models considering strain rate effect were summarized, and a simplified model evaluating dynamic compressive strength of post-fire concrete confined by CFRP sheets was proposed, which can provide evidence for engineering emergency repair after fire accidents.
To investigate the bonding performance between Northeast larch (Larix gmelinii) and carbon fiber-reinforced polymer (CFRP) as well as basalt fiber-reinforced polymer (BFRP), this paper systematically analyzes the effects of fiber-reinforced polymer (FRP) type, bonding length, and bonding width on the mechanical behavior of the interface through single shear pull-out tests. A total of 20 FRP-timber specimens were designed for the tests, and their ultimate bearing capacity, failure mode, strain distribution, and load-slip relationship were measured. The results indicate that BFRP exhibits greater ductility, averaging 35.04% higher than CFRP, while CFRP demonstrates significantly higher tensile strength, exceeding BFRP by 83.41%. The failure mode of CFRP specimens primarily involves debonding at the timber-adhesive interface, whereas BFRP specimens mainly exhibit debonding at the FRP-adhesive interface. An increase in bonding width leads to a larger bonding area, resulting in a higher ultimate load capacity. However, due to the limitations of effective bonding length, the ultimate load increases rapidly when bonding length is raised from 50 mm to 100 mm, but further increases in length yield diminish returns in load capacity. Strain distribution analysis reveals that the strain in FRP decreases linearly along the bonding length, with peak strain increasing as bonding width decreases. Based on the experimental data, a predictive model for interfacial debonding load capacity was developed, demonstrating good robustness with an average coefficient of determination (R2) of 0.65. This model provides a reliable theoretical reference for evaluating the ultimate load capacity of FRP-reinforced Northeast larch structures, while also offering essential experimental evidence and theoretical support for FRP reinforcement design in Northeast larch wood structures.
This study focuses on the core issue of sustainably utilizing shells to enhance the performance of cement mortar. The influence of shell powder on the slump flow, setting time, mechanical strengths, drying shrinkage rate and carbonation depth of cement mortar is investigated. The flexural and compressive strengths of cement mortar incorporating calcium formate after 12 h, 3-day and 28-day curing periods are examined. The effect of basalt fibers on the attenuation of cement mortar’s mechanical properties (flexural and compressive strengths) after NaCl freeze–thaw cycles is also studied. Scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) is employed to elucidate the underlying mechanisms. Results show that the slump flow, setting time and mechanical strengths have cubic function relationships with the shell powder’s mass ratio, while the drying shrinkage rate and carbonation depth follow quadratic function changes. Cement mortar with 15% shell powder by mass of the total binder materials demonstrates the highest slump flow and mechanical strengths. At this shell powder mass ratio, cement mortar shows the lowest drying shrinkage rate and carbonation depth. Calcium formate positively influences the 12-h mechanical strengths. After 3 days of curing, the mechanical strengths of cement mortar with 0.3% calcium formate are the highest. The calcium carbonate powder reduces the drying shrinkage rate of mortar and increases the content of Ca and C elements. The mass ratio of calcium formate exhibits a negative correlation with the cement mortar’s mechanical strengths after being cured for 28 days. The addition of basalt fibers enhances resistance to chloride salt freeze–thaw and dry-wet alternations erosion performance. These findings will provide a sustainable and effective strategy for utilizing agricultural by-products in concrete structures.