SHIJIE JIANG

SHIJIE JIANG

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 January 2022 in Polymers
Verified
Journal Article
Open access
PDF file
SJSHIJIE JIANG
SHIJIE JIANG
KHKe Hu
Ke Hu
YZYang Zhan
Yang Zhan
CZChunyu Zhao
Chunyu Zhao
XLXiaopeng LI
Xiaopeng LI
Material extrusion (ME), one of the most widely used additive manufacturing technique, has the advantages of freedom of design, wide range of raw materials, strong ability to manufacture complex products, etc. However, ME products have obvious surface defects due to the layer-by-layer manufacturing characteristics. To reveal the generation mechanism, the three-dimensional surface roughness (3DSR) of ME products was investigated theoretically and experimentally. Based on the forming process of bonding neck, the 3DSR theoretical model in two different directions (vertical and parallel to the fiber direction) was established respectively. The preparation of ME samples was then completed and a series of experimental tests were performed to determine their surface roughness with the laser microscope. Through the comparison between theoretical and experimental results, the proposed model was validated. In addition, sensitivity analysis is implemented onto the proposed model, investigating how layer thickness, extrusion temperature, and extrusion width influence the samples’ surface roughness. This study provides theoretical basis and technical insight into improving the surface quality of ME products.

29 May 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SJSHIJIE JIANG
SHIJIE JIANG
PCPIFENG CHEN
PIFENG CHEN
YZYang Zhan
Yang Zhan
CZChunyu Zhao
Chunyu Zhao
Material extrusion (ME), an extrusion-based rapid prototyping technique, has been extensively studied to manufacture final functional products, whose forming quality is significantly influenced by the melt flow behavior (MFB) inside the extrusion liquefier. Applied vibration has a great potential to improve the MFB, and thereby promote the forming quality of the built product. To reveal the mechanism, a dynamic model of the melt flow behavior (DMMFB) is established based on fluid dynamics, Tanner nonlinear constitutive equation and Newton’s power law equation. The MFB, i.e., pressure drop, shear stress and apparent viscosity, is investigated without and with different vibration applied. The corresponding finite element analysis (FEA) is then carried out. From the comparison between DMMFB and FEA results, it is concluded that the proposed model is reliable. When vibration is applied onto the extrusion liquefier, the time-domain MFB will change periodically. Its effective value decreases significantly, and further decreases with the increase of vibration frequency or amplitude. This paper provides the theoretical basis to improve the MFB by applied vibration, and thereby to enhance the forming quality of ME products.

18 February 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SJSHIJIE JIANG
SHIJIE JIANG
TDTiankuo Dong
Tiankuo Dong
YZYang Zhan
Yang Zhan
WDWeibing Dai
Weibing Dai
MZMing Zhan
Ming Zhan
Due to the stratified nature of the manufacturing process, material extrusion (ME) parts have lower mechanical properties than those fabricated by traditional technology. This is one of the most significant defects hindering the development and application of this rapid prototyping technique. In this paper, vibration was applied to the ME process by using piezoelectric ceramics for the first time to improve the mechanical properties of the built parts. The vibrating ME equipment was established, and the specimens processed in different build directions were individually fabricated without applied vibration and with different applied vibrations. To quantify the effect of applied vibration on their mechanical properties and to summarize the influencing rule, a series of experimental tests were then performed on these specimens. A comparison between the testing results shows that the tensile strength and plasticity of the specimens, especially those processed in the Z direction, can be obviously improved by applied vibration. The orthogonal anisotropy is decreased obviously. The improvement becomes greater with increasing vibration frequency or amplitude. From the microscopic point of view, it can be seen that applied vibration can reduce the part’s defects of porosity and inclusion as well as separation between layers and, thereby, improve the bonding strength.

6 December 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SJSHIJIE JIANG
SHIJIE JIANG
YSYinfang Shi
Yinfang Shi
SBSIYAJEU KATTA YANNICK BERNARD
SIYAJEU KATTA YANNICK BERNARD
MZMing Zhan
Ming Zhan
CZChunyu Zhao
Chunyu Zhao
CLChangyou Li
Changyou Li
Material extrusion (ME), an additive manufacturing technique, can fabricate parts almost without geometrical limitations. With the growing application of ME parts, especially in actual working conditions, the dynamic characteristics are needed to be studied to accurately determine their reliability. This study provides an experimental validation of the theoretical model for predicting the dynamic characteristics of ME plates fabricated with three different key processing parameters, i.e., extrusion width, layer height and build direction. The model is set up based on the bidirectional beam function combination method, and a series of experimental tests are performed. It is found that different processing parameters result in the material properties of the samples to vary, thus leading to different dynamic characteristics. Through the comparison between predictions and measurements, it is shown that the influencing trend of the processing parameters is predicted precisely. The theoretical model gives reliable predictions in dynamic characteristics of ME plates. The natural frequency discrepancy is below 13.4%, and the predicted mode shapes are the same as the measured ones. This present work provides theoretical basis and technical support for further research in improving the dynamic performance of ME products, and helps extend the applications of this technique.

1 June 2023 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Closed access
SBSIYAJEU KATTA YANNICK BERNARD
SIYAJEU KATTA YANNICK BERNARD
SJSHIJIE JIANG
SHIJIE JIANG
BWBangchun Wen
Bangchun Wen
HLHe Li
He Li

16 April 2024 in International Journal of Material Forming
Verified
Journal Article
Closed access
PDF file
SJSHIJIE JIANG
SHIJIE JIANG
CYChaoqun Yun
Chaoqun Yun
HYHongwei Ying
Hongwei Ying
JCJiaqi Chen
Jiaqi Chen
CZChunyu Zhao
Chunyu Zhao
HYHuisheng Yao
Huisheng Yao