Humberto Julian Mandujano-Ramírez

Dr. Humberto Julian Mandujano-Ramírez

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 April 2026 in Hydrogen
Verified
Journal Article
Open access
PDF file
SMSergio Martinez-Vargas
Sergio Martinez-Vargas
JFJosé Enrique Flores-Chan
José Enrique Flores-Chan
Humberto Julian Mandujano-RamírezHumberto Julian Mandujano-Ramírez
Humberto Julian Mandujano-Ramírez
SPSalatiel Pérez-Montejo
Salatiel Pérez-Montejo
Jose Damian Calan CancheJose Damian Calan Canche
Jose Damian Calan Canche
CPCristobal Patino-Carachure
Cristobal Patino-Carachure
Hydrogen (H2) was produced from recycled aluminum microparticles (180–250, 300–425, and 425–500 μm) via alkaline hydrolysis using a 1.0 M NaOH solution to enhance oxide layer removal and aluminum dissolution. Maximum hydrogen flow rates of approximately 13, 15, and 19 mL·min−1 were obtained, confirming that smaller particle sizes promote faster reaction rates due to increased specific surface area. The hydrogen evolution exhibited two-stage kinetic behavior: an initial stage characterized by rapid aluminum dissolution and increasing H2 production, followed by a gradual decline associated with the formation of a passivating Al(OH)3 layer. Despite the higher reaction rates observed for smaller particles, the maximum cumulative hydrogen production was obtained for the intermediate particle size (363 µm, 132 mL), compared to 106 mL and 102 mL for 215 µm and 463 µm, respectively, indicating a trade-off between surface area and passivation effects. Kinetic analysis based on the shrinking core model showed excellent agreement (R2 = 99.94–99.97%), with rate constants of 0.137, 0.064, and 0.050 min−1. The relationship k ∝ d−n (n ≈ 1.4) suggests a mixed kinetic regime involving both surface reaction and diffusion through the Al(OH)3 layer. These findings indicate that hydrogen generation can be modulated by particle size; however, the relatively low flow rates and yields limit its immediate practical applicability.

25 February 2026 in Preprints.org
Verified
Preprint
Open access
PDF file
SMSergio Martinez-Vargas
Sergio Martinez-Vargas
JFJosé Enrique Flores-Chan
José Enrique Flores-Chan
Humberto Julian Mandujano-RamírezHumberto Julian Mandujano-Ramírez
Humberto Julian Mandujano-Ramírez
SPSalatiel Pérez-Montejo
Salatiel Pérez-Montejo
Jose Damian Calan CancheJose Damian Calan Canche
Jose Damian Calan Canche
CPCristobal Patino-Carachure
Cristobal Patino-Carachure
Hydrogen (H2) was produced using recycled aluminum (Al), with particle sizes of 180-250 μm, 300-420 μm and 420-530 μm. A 1.0 M NaOH solution was employed to enhance aluminum dissolution and maximize hydrogen release. During a 30-minute evaluation, peak hydrogen flow rates of approximately 14, 16, and 23 ml/min were obtained, depending on particle size reduction. The H₂ flow behavior for the three size ranges can be divided into two distinct stages: the first corresponds to the initial contact between Al and the NaOH solution, where hydrogen production increases until reaching a maximum; the second stage follows, characterized by a gradual decline in H₂ generation to nearly zero toward the end of the test. These findings indicate that smaller particle sizes promote a more intense hydrogen release during the first stage, due to the higher aluminum dissolution rate, while in the second stage, production decreases significantly as the formation of an oxide layer slows down Al dissolution. For fuel cell applications, particle size and sample mass can thus be adjusted to regulate the desired hydrogen flow rate. XRD and SEM analysis demonstrated the consistency of the equations describing the hydrogen production reaction phenomenon in these aluminum-based equations.

31 December 2024
Verified
Book Chapter
Closed access
ATAna Paulina Toxqui-De La Torre
Ana Paulina Toxqui-De La Torre
Humberto Julian Mandujano-RamírezHumberto Julian Mandujano-Ramírez
Humberto Julian Mandujano-Ramírez
SMSergio Martinez-Vargas
Sergio Martinez-Vargas
CPCristobal Patino-Carachure
Cristobal Patino-Carachure
Fullerenes are symmetrical carbon nanostructures zero dimensional with hybridation sp2-bondend carbon atoms (with four valence electrons) arranged in pentagonal and hexagonal rings that form a hollow closed-cage structure. Fullerene C30 is not symmetrical, specifically has 12 pentagonal and 5 hexagonal rings that form a barrel-like shape where the 5 hexagons form the body of the barrel, and the 12 pentagons are located in the bases of the barrel. Doped fullerenes were built by placing a heteroatom (as a boron or a nitrogen atom, with three or five valence electrons, respectively) at different doping sites. Doped fullerenes were optimized in presence of CO2 using density functional theory (DFT) through PBE functional and 6-31G(d,p) basis set. The CO2 adsorption energy on doped fullerenes were determined.

30 December 2025
Verified
Book Chapter
Closed access
JSJuan Sierra-Grajeda
Juan Sierra-Grajeda
SFSandra Figueroa
Sandra Figueroa
JCJosé Enrique Flores Chan
José Enrique Flores Chan
Humberto Julian Mandujano-RamírezHumberto Julian Mandujano-Ramírez
Humberto Julian Mandujano-Ramírez
This work presents a comparative performance analysis of two proton exchange membrane [PEM] electrolyzer prototypes featuring different flow fields. A square pin-type design is compared wit a circular pin-type design and a commercial design, with the objective of determining their capacity to produce hydrogen and to optimize their design to prevent bubble accumulation in the channels. The results showed that the conditioning of the membrane electrode assembly [MEA] considerably impacts its performance. The circular pin-type design achieved superior performance, producing a greater amount of hydrogen [546 mL at 2.4 V] compared to the square pin-type design [372 mL9 and a commercial electrolyzer [300 mL]. This configuration improves mass transport by preventing bubble accumulation in the channels, demonstrating the critical importance of flow field geometry for process efficiency.

14 August 2026
Verified
Book Chapter
Closed access
JAJosé Ángel Arrocha-Rojas
José Ángel Arrocha-Rojas
Humberto Julian Mandujano-RamírezHumberto Julian Mandujano-Ramírez
Humberto Julian Mandujano-Ramírez
JCJosé Enrique Flores Chan
José Enrique Flores Chan
SMSergio Martinez-Vargas
Sergio Martinez-Vargas
CO₂ adsorption on fullerene C₂₇B (D₂ symmetry) with a boron atom located at the junction of three pentagonal faces (C₂₇B-D2-ppp) was studied using Density Functional Theory (DFT). Calculations were performed employing the PBE functional, the 6-31G(d,p) basis set, and the D3(BJ) dispersion correction, including geometry optimization, vibrational analysis, molecular electrostatic potential (MEP), HOMO–LUMO frontier orbitals, and BSSE-corrected adsorption energies. It was observed that boron doping modified the geometric, vibrational and electronic properties of the fullerene, producing changes in the electrostatic distribution and frontier orbitals. The interaction with CO₂ showed differences with respect to the pristine fullerene C₂₈ in both geometry and electronic properties. The obtained results allow the analysis of the effect of boron doping on CO₂ adsorption and on the geometric, electronic, and vibrational properties of the adsorbent–adsorbate system.

14 August 2026
Verified
Book
Closed access
Humberto Julian Mandujano-RamírezHumberto Julian Mandujano-Ramírez
Humberto Julian Mandujano-Ramírez
SFSandra Figueroa
Sandra Figueroa
SPSalatiel Pérez-Montejo
Salatiel Pérez-Montejo
AGAaron Flores Gil
Aaron Flores Gil
El presente Handbook “Ciencia de materiales aplicada a la ingeniería de sistemas energéticos”, reúne diez capítulos que presentan resultados de investigación relacionados con el desarrollo, caracterización y aplicación de materiales y tecnologías vinculadas con la generación, conversión y aprovechamiento de la energía. Los trabajos integran diferentes enfoques experimentales, computacionales y de modelado, reflejando el carácter interdisciplinario de la investigación en materiales y energía. Entre los temas abordados se encuentran el aprovechamiento de materiales reciclados para la generación de hidrógeno, el comportamiento electroquímico de aleaciones, las celdas de combustible, la captura de CO2 mediante materiales funcionales, la síntesis verde, la producción de biocombustibles y la caracterización avanzada de materiales. Asimismo, se incluyen estudios relacionados con el análisis termo-estructural de grafito por medio de sistemas láser, y el diagnóstico de microfisuras en componentes sometidos a condiciones de operación, destacando la importancia de la confiabilidad y seguridad de los sistemas energéticos.