José Enrique Flores-Chan

José Enrique Flores-Chan


Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 April 2026 in Hydrogen
Verified
Journal Article
Open access
PDF file
SMSergio Martinez-Vargas
Sergio Martinez-Vargas
JFJosé Enrique Flores-Chan
José Enrique Flores-Chan
Humberto Julian Mandujano-RamírezHumberto Julian Mandujano-Ramírez
Humberto Julian Mandujano-Ramírez
SPSalatiel Pérez-Montejo
Salatiel Pérez-Montejo
Jose Damian Calan CancheJose Damian Calan Canche
Jose Damian Calan Canche
CPCristobal Patino-Carachure
Cristobal Patino-Carachure
Hydrogen (H2) was produced from recycled aluminum microparticles (180–250, 300–425, and 425–500 μm) via alkaline hydrolysis using a 1.0 M NaOH solution to enhance oxide layer removal and aluminum dissolution. Maximum hydrogen flow rates of approximately 13, 15, and 19 mL·min−1 were obtained, confirming that smaller particle sizes promote faster reaction rates due to increased specific surface area. The hydrogen evolution exhibited two-stage kinetic behavior: an initial stage characterized by rapid aluminum dissolution and increasing H2 production, followed by a gradual decline associated with the formation of a passivating Al(OH)3 layer. Despite the higher reaction rates observed for smaller particles, the maximum cumulative hydrogen production was obtained for the intermediate particle size (363 µm, 132 mL), compared to 106 mL and 102 mL for 215 µm and 463 µm, respectively, indicating a trade-off between surface area and passivation effects. Kinetic analysis based on the shrinking core model showed excellent agreement (R2 = 99.94–99.97%), with rate constants of 0.137, 0.064, and 0.050 min−1. The relationship k ∝ d−n (n ≈ 1.4) suggests a mixed kinetic regime involving both surface reaction and diffusion through the Al(OH)3 layer. These findings indicate that hydrogen generation can be modulated by particle size; however, the relatively low flow rates and yields limit its immediate practical applicability.

25 February 2026 in Preprints.org
Verified
Preprint
Open access
PDF file
SMSergio Martinez-Vargas
Sergio Martinez-Vargas
JFJosé Enrique Flores-Chan
José Enrique Flores-Chan
Humberto Julian Mandujano-RamírezHumberto Julian Mandujano-Ramírez
Humberto Julian Mandujano-Ramírez
SPSalatiel Pérez-Montejo
Salatiel Pérez-Montejo
Jose Damian Calan CancheJose Damian Calan Canche
Jose Damian Calan Canche
CPCristobal Patino-Carachure
Cristobal Patino-Carachure
Hydrogen (H2) was produced using recycled aluminum (Al), with particle sizes of 180-250 μm, 300-420 μm and 420-530 μm. A 1.0 M NaOH solution was employed to enhance aluminum dissolution and maximize hydrogen release. During a 30-minute evaluation, peak hydrogen flow rates of approximately 14, 16, and 23 ml/min were obtained, depending on particle size reduction. The H₂ flow behavior for the three size ranges can be divided into two distinct stages: the first corresponds to the initial contact between Al and the NaOH solution, where hydrogen production increases until reaching a maximum; the second stage follows, characterized by a gradual decline in H₂ generation to nearly zero toward the end of the test. These findings indicate that smaller particle sizes promote a more intense hydrogen release during the first stage, due to the higher aluminum dissolution rate, while in the second stage, production decreases significantly as the formation of an oxide layer slows down Al dissolution. For fuel cell applications, particle size and sample mass can thus be adjusted to regulate the desired hydrogen flow rate. XRD and SEM analysis demonstrated the consistency of the equations describing the hydrogen production reaction phenomenon in these aluminum-based equations.