The release of fragments from plastic products, that is, secondary microplastics, is a major concern in the context of the global plastic pollution. Currently available (thermoplastic) polyurethanes [(T)PU] are not biodegradable and therefore should be recycled. However, the ester bond in (T)PUs might be sufficiently hydrolysable to enable at least partial biodegradation of polyurethane particles. Here, we investigated biodegradation in compost of different types of (T)PU to gain insights into their fragmentation and biodegradation mechanisms. The studied (T)PUs varied regarding the chemistry of their polymer backbone (aromatic/aliphatic), hard phase content, cross-linking degree, and presence of a hydrolysis-stabilizing additive. We developed and validated an efficient and non-destructive polymer particle extraction process for partially biodegraded (T)PUs based on ultrasonication and density separation. Our results showed that biodegradation rates and extents decreased with increasing cross-linking density and hard-segment content. We found that the presence of a hydrolysis stabilizer reduced (T)PU fragmentation while not affecting the conversion of (T)PU carbon into CO₂. We propose a biodegradation mechanism for (T)PUs that includes both mother particle shrinkage by surface erosion and fragmentation. The presented results help to understand structure-degradation relationships of (T)PUs and support recycling strategies.

Microplastics have been detected in various food types, suggesting inevitable human exposure. A major fraction may originate from aerial deposition and could be contaminated by ubiquitous pollutants such as polycyclic aromatic hydrocarbons (PAHs). While data on the sorption of pollutants to microplastics are abundant, the subsequent desorption in the gastrointestinal tract (GIT) is less understood. This prompted us to systematically investigate the release of microplastics-sorbed PAHs at realistic loadings (44-95 ng/mg) utilizing a physiology-based in vitro model comprising digestion in simulated saliva, gastric, and small and large intestinal fluids. Using benzo[a]pyrene as a representative PAH, desorption from different microplastics based on low density polyethylene (LDPE), thermoplastic polyurethanes (TPUs), and polyamides (PAs) was investigated consecutively in all four GIT fluid simulants. The cumulative relative desorption (CRD) of benzo[a]pyrene was negligible in saliva simulant but increased from gastric (4 ± 1% - 15 ± 4%) to large intestinal fluid simulant (21 ± 1% - 29 ± 6%), depending on the polymer type. CRDs were comparable for ten different microplastics in the small intestinal fluid simulant, except for a polydisperse PA-6 variant (1-10 μm), which showed an exceptionally high release (51 ± 8%). Nevertheless, the estimated contribution of microplastics-sorbed PAHs to total human PAH dietary intake was very low (≤0.1%). Our study provides a systematic data set on the desorption of PAHs from microplastics in GIT fluid simulants.

Understanding the occurrence and transformation of microplastics when released into the environment is essential for risk assessment. The use of biodegradable polymers in agriculture can help to reduce microplastic accumulation in soil, since released fragments of such materials are not persistent and are further transformed into CO₂ and biomass (Wohlleben et al., 2023). To be able to monitor the fragmentation and biodegradation of these materials in soil, a validated extraction protocol is needed, which does not induce changes in the chemical and particle properties, additionally it should show high recoveries and matrix removal efficiency. A density-based extraction method in the centrifuge has the potential to remove a high amount of the soil matrix and is very selective for the polymer at the same time. Here we developed an efficient and non-destructive extraction protocol for biodegradable fragments from different soils using sequential centrifugation steps with varying densities and a freezing approach for sample collection. Although the focus of the present study was on biodegradable fragments, the technique can also be used for other types of microplastics with similar or lower density than the one tested for the method validation, but additional recovery tests for the target analyte are recommended. • A density-based extraction method for microplastics from soil, validated by recovery and stability tests using biodegradable polymers • Vessel changes and harsh chemical treatments are kept to a minimum

Soil-biodegradable mulch films offer a sustainable alternative to conventional plastics in agriculture, especially where recollection or recycling are impractical. However, biodegradation of these materials must not result in the formation of persistent microplastics. This study investigates the fragmentation and biodegradation of the certified soil-biodegradable mulch film ecovio® M2351 in standardized laboratory conditions (ISO 17556). The material was incubated in agricultural soil in two different forms: cryomilled fragments and 1 cm² film pieces. Fragment formation was quantified using μ-FTIR microscopy. Biodegradation as well as fragmentation kinetics were modelled by the open-source mechanistic FRAGMENT-MNP model. Results demonstrate that fragmentation is a transient phase within the biodegradation process, with particle counts transitionally peaking, then declining as mineralization progresses. Cryomilled fragments exhibited faster biodegradation and more pronounced fragmentation than larger film pieces. When biodegradation experiments were stopped, more than 90 % of the polymeric carbon was converted into CO₂ and residual fragments showed comparable chemical composition to the original material but showed significantly reduced molar masses, indicating that the biodegradation was still progressing. This is supported by the model, predicting that particle concentrations will decrease to below one particle per gram of soil within 600-700 days for both scenarios. These findings confirm that certified soil-biodegradable polymers like ecovio® M2351 do not form persistent microplastics. The combined experimental and modelling approach provides mechanistic insights into the interplay between fragmentation and mineralization and could be further improved by additional measurements of fragments <25 μm and of the polymer mass in the dissolved phase. In future, field data can support the extrapolation of the model predictions to the real-world.

Extracting microplastics from complex matrices poses challenges due to the potential impact of harsh chemical treatments on microplastic properties. For fate and hazard assessment reliable techniques are needed to not only quantify the particle number but also to assess the physicochemical properties of environmental microplastics with minimum changes induced by extraction. Here we present the method development for an innovative and non-destructive extraction protocol based on a switchable calcium chloride density separation column. In contrast to commonly reported extraction protocols, the presented technique is suitable for targeted microplastic property analysis (e.g., surface chemistry and texture) by keeping chemical treatments (such as oxidation and enzymatic digestion) to a minimum. By adjusting the temperature we can control the aggregate state of the highly concentrated salt solution, allowing to separate the microplastics from matrix by cutting of purified, solidified samples. Harsh chemical treatments are avoided, as well as obstruction of microplastic extraction by adsorption to matrix components when passing the tap at the bottom of traditional density separation funnels.