Jaime L. Lozada

Dr. Jaime L. Lozada


Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2011 in The Journal of Prosthetic Dentistry
Verified
Journal Article
Closed access
JLJaime L. Lozada
Jaime L. Lozada
CGCharles Goodacre
Charles Goodacre
AAAladdin J. Al-Ardah
Aladdin J. Al-Ardah
AGAntoanela Garbacea
Antoanela Garbacea

2 October 2025 in Journal of Maxillofacial and Oral Surgery
Verified
Journal Article
Open access
PDF file
EZEkaterina Zernitckaia
Ekaterina Zernitckaia
JLJaime L. Lozada
Jaime L. Lozada
AYA. I. Yaremenko
A. I. Yaremenko
ARA. P. Reutova
A. P. Reutova
MMM. A. Markova
M. A. Markova
Zhanna LyutovaZhanna Lyutova
Zhanna Lyutova
Introduction: Modern maxillofacial surgery increasingly emphasizes the restoration and regeneration of oral tissues, particularly the hard tissues of the jaws. Bone defects may arise from disease, trauma, or congenital anomalies. Guided bone regeneration (GBR) using barrier membranes is a widely accepted technique for managing such defects. However, standard titanium and PTFE membranes require a secondary surgical procedure for removal, limiting their clinical convenience. Although resorbable collagen membranes avoid this issue, they often lack sufficient structural integrity, making them less effective for vertical or complex bone augmentation. Aim: This study aimed to evaluate the physicochemical properties of biodegradable membranes based on polylactic acid (PLA), its copolymers, and composite materials for potential use in GBR. In addition, the effects of sterilizing doses of ionizing radiation were assessed to determine an optimal sterilization protocol. Materials and Methods: The materials tested included pure PLA, PLA reinforced with hydroxyapatite (PLA/HAP), and polyglycolic acid (PLGA) in two compositions: 85:15 and 60:40. Physicochemical properties and responses to electron beam sterilization (25 kGy) were analyzed. Biodegradation was evaluated in phosphate-buffered saline at 37 °C. Sample morphology and molecular structure were assessed using infrared (IR) spectroscopy and scanning electron microscopy (SEM). Results: After one month, PLGA (60:40) samples exhibited approximately 40% mass loss, while PLGA (85:15) showed only about 5%. Pure PLA remained largely intact, with less than 1% mass loss. Non-irradiated PLA/HAP samples degraded inconsistently, with mass loss ranging from negligible to 19%, while irradiated PLA/HAP samples exhibited minimal degradation (up to 2%). This increased stability may be due to radiation-induced crystallinity, though further investigation is needed. In some cases, a slight mass increase was observed, possibly due to water diffusion into deeper composite layers. Among all tested materials, pure PLA demonstrated the highest stability, retaining its shape and showing minimal degradation throughout the study period. Conclusion: The results support the potential use of PLA and its copolymers for developing biodegradable membranes in GBR. Ionizing radiation appears to be a viable sterilization method, with minimal impact on material integrity. Further optimization of physicochemical properties and degradation behavior is warranted to facilitate clinical application in maxillofacial surgery.

1 May 2019 in Journal of the California Dental Association
Verified
Journal Article
Closed access
JLJaime L. Lozada
Jaime L. Lozada
CHCarolina Herrera
Carolina Herrera
BGBrian Goodacre
Brian Goodacre
AAAladdin Al-Ardah
Aladdin Al-Ardah
ESErik Sahl
Erik Sahl
Three-dimensional printing is rapidly evolving in dentistry. In the field of implant dentistry, countless numbers of laboratory and clinical applications are consistently being developed. This review article describes the application of three different uses of stereolithographic 3D printing, including diagnostic bone models, modified surgical guides and bone reduction guides. Furthermore, the use of 3D-bioprinting technology in printing bone scaffolds that could be used during guided bone regeneration (GBR) procedures is also presented.