Choonsup Lee

Dr. Choonsup Lee


Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 November 2005 in Nano Letters
Verified
Journal Article
Closed access
CLChoonsup Lee
Choonsup Lee
SBSam Y. Bae
Sam Y. Bae
SMSohrab Mobasser
Sohrab Mobasser
HMHarish Manohara
Harish Manohara

17 October 2018 in IEEE Transactions on Terahertz Science and Technology
Verified
Journal Article
Closed access
JSJose V. Siles
Jose V. Siles
KCKen B. Cooper
Ken B. Cooper
CLChoonsup Lee
Choonsup Lee
RLRobert H. Lin
Robert H. Lin
GCGoutam Chattopadhyay
Goutam Chattopadhyay
IMImran Mehdi
Imran Mehdi
We report on the design, fabrication and test of a new generation all-solid-state frequency multiplied terahertz sources providing up to ten times more output power at room temper-ature than the previous state-of-the-art. These new sources benefit from both a novel ‘on-chip’ power combined topology recently introduced and new devices and circuits thoroughly optimized for high power operation. Prototypes at 180 GHz, 240 GHz, 340 GHz, 530 GHz, 1 THz and 1.6 THz have been designed, fabricated, and tested. All sources exhibit record performances with conversion efficiencies reaching the theoret-ical limit predicted by physics-based numerical models. Meas-ured nominal room temperature output power levels are 500 mW at 180 GHz, 110 mW at 220 GHz, 35 mW at 330 GHz, 30 mW at 550 GHz, 2 mW at 1.03 THz and 0.7 mW at 1.64 THz.

18 April 2012 in IEEE Transactions on Terahertz Science and Technology
Verified
Journal Article
Closed access
ATAik Yean Tang
Aik Yean Tang
ESErich Schlecht
Erich Schlecht
RLRobert Lin
Robert Lin
GCGoutam Chattopadhyay
Goutam Chattopadhyay
CLChoonsup Lee
Choonsup Lee
JSJan Stake
Jan Stake
We present a self-consistent electro-thermal model for multi-anode Schottky diode multiplier circuits. The thermal model is developed for an n-anode multiplier via a thermal resistance matrix approach. The nonlinear temperature responses of the material are taken into consideration by using a linear temperature-dependent approximation for the thermal resistance. The electro-thermal model is capable of predicting the hot spot temperature, providing useful information for circuit reliability study as well as high power circuit design and optimization. Examples of the circuit analysis incorporating the electro-thermal model for a substrateless- and a membrane-based multiplier circuits, operating up to 200 GHz, are demonstrated. Compared to simulations without thermal model, the simulations with electro-thermal model agree better with the measurement results. For the substrateless multiplier, the error between the simulated and measured peak output power is reduced from ~ 13% to ~ 4% by including the thermal effect.

1 January 2009
Verified
Conference Paper
Closed access
TBTomas Bryllert
Tomas Bryllert
KCKen B. Cooper
Ken B. Cooper
RDRobert J. Dengler
Robert J. Dengler
NLNuria Llombart
Nuria Llombart
GCGoutam Chattopadhyay
Goutam Chattopadhyay
PSPeter H. Siegel
Peter H. Siegel
We present the hardware and the experimental results from a 600 GHz imaging radar with sub-centimeter resolution in all three spatial dimensions. The FMCW radar transceiver is built on a back-end of commercial microwave components - with a front-end of custom designed frequency multipliers and mixers. The optics consists of a 40 cm diameter ellipsoidal primary reflector with a 4 m focal length. The acquired images will be compared with those achieved with a more traditional sub-millimeter wave active imaging technique.

30 July 2024 in IEEE Transactions on Terahertz Science and Technology
Verified
Journal Article
Closed access
JSJose V. Siles
Jose V. Siles
AMAlain Eric Maestrini
Alain Eric Maestrini
CLChoonsup Lee
Choonsup Lee
RLRobert Lin
Robert Lin
IMImran Mehdi
Imran Mehdi
We introduce a groundbreaking 2 THz front-end suitable for space use, operating at room temperature. Our objective is to measure high-altitude 3D winds for precise Sun-Earth energy coupling analysis. Employing Schottky diode-based mixers and multipliers, we've developed a solid-state receiver with Double Side-Band (DSB) sensitivity below 8000K. This sensitivity enables the measurement of atomic oxygen in the approximate 100-200 km altitude range. Our approach encompasses design, fabrication, and sensitivity assessment of the receiver front-end.

1 May 2012
Verified
Conference Paper
Closed access
PDF file
TRTheodore Reck
Theodore Reck
JSJose Siles
Jose Siles
CJCecile Jung
Cecile Jung
JGJohn Gill
John Gill
CLChoonsup Lee
Choonsup Lee
KCKen Cooper
Ken Cooper
Heterodyne terahertz (0.3 - 3THz) imaging systems are currently limited to single or a low number of pixels. Drastic improvements in imaging sensitivity and speed can be achieved by replacing single pixel systems with an array of detectors. This paper presents an array topology that is being developed at the Jet Propulsion Laboratory based on the micromachining of silicon. This technique fabricates the array's package and waveguide components by plasma etching of silicon, resulting in devices with precision surpassing that of current metal machining techniques. Using silicon increases the versatility of the packaging, enabling a variety of orientations of circuitry within the device which increases circuit density and design options. The design of a two-pixel transceiver utilizing a stacked architecture is presented that achieves a pixel spacing of 10mm. By only allowing coupling from the top and bottom of the package the design can readily be arrayed in two dimensions with a spacing of 10mm x 18mm.