We report on the design, fabrication and test of a new generation all-solid-state frequency multiplied terahertz sources providing up to ten times more output power at room temper-ature than the previous state-of-the-art. These new sources benefit from both a novel ‘on-chip’ power combined topology recently introduced and new devices and circuits thoroughly optimized for high power operation. Prototypes at 180 GHz, 240 GHz, 340 GHz, 530 GHz, 1 THz and 1.6 THz have been designed, fabricated, and tested. All sources exhibit record performances with conversion efficiencies reaching the theoret-ical limit predicted by physics-based numerical models. Meas-ured nominal room temperature output power levels are 500 mW at 180 GHz, 110 mW at 220 GHz, 35 mW at 330 GHz, 30 mW at 550 GHz, 2 mW at 1.03 THz and 0.7 mW at 1.64 THz.
9 September 2019 in IEEE Antennas and Propagation Magazine
Small satellites (smallsats) provide low-cost access to space and have historically been used for flight technology demonstrations and limited-function space science activities. Novel antenna technologies have enabled high-performance smallsat telecommunications, science in Earth orbit, and the first CubeSat mission to deep space. In the past five years, technologists at NASA's Jet Propulsion Laboratory (JPL) have designed, tested, and successfully flown these innovative and enabling smallsat antennas. This article describes these innovations and their impact on smallsat performance for recent and future NASA missions.
16 November 2018 in IEEE Transactions on Terahertz Science and Technology
This paper presents a lens antenna that scans the beam using an integrated piezomotor at submillimeter-wave frequencies. The lens antenna is based on the concept presented by Llombart et al. in 2011, a leaky-wave waveguide feed in order to achieve wide angle scanning and seamless integration with the receiver. The lens is translated from the origin of the waveguide producing the scanning of the beam over a 50 $^\circ$ field of view (FoV) (or about 6.25 beamwidths) with a maximum scanning loss of 1 dB. The lens movement is achieved with a piezoelectric motor that is integrated within the antenna and receiver block. A prototype was built and measured at 550 GHz achieving scanning beam angles close to 20 $^\circ$ with only 0.6 dB of loss. The scanning of the 50 $^\circ$ FoV, which corresponds to a lens displacement of approximately 2 mm, takes about 0.9 s achieving a scanning rate of 0.75 Hz of the FoV. The accuracy in continuous mode of the piezoactuator has been measured to be less than $28\,\mu$ m in the worse of cases for displacements of 2 mm, which corresponds to a beam steering of 0.76 $^\circ$ , much smaller than the antenna half-power beamwidth of 8 $^\circ$ .
18 April 2012 in IEEE Transactions on Terahertz Science and Technology
We present a self-consistent electro-thermal model for multi-anode Schottky diode multiplier circuits. The thermal model is developed for an n-anode multiplier via a thermal resistance matrix approach. The nonlinear temperature responses of the material are taken into consideration by using a linear temperature-dependent approximation for the thermal resistance. The electro-thermal model is capable of predicting the hot spot temperature, providing useful information for circuit reliability study as well as high power circuit design and optimization. Examples of the circuit analysis incorporating the electro-thermal model for a substrateless- and a membrane-based multiplier circuits, operating up to 200 GHz, are demonstrated. Compared to simulations without thermal model, the simulations with electro-thermal model agree better with the measurement results. For the substrateless multiplier, the error between the simulated and measured peak output power is reduced from ~ 13% to ~ 4% by including the thermal effect.
20 October 2020 in IEEE Transactions on Antennas and Propagation
We demonstrate a silicon (Si) – gallium arsenide (GaAs) semiconductor based holographic metasurface antenna operating at 94 GHz. The metasurface antenna molds the radiated beam by resorting to a holographic approach involving the modulation of a guided-mode generated by a pillbox beam former. The pillbox beam former is fed by three integrated horns in Substrate Integrated Waveguide (SIW) technology located in the focal plane of the parabolic reflector of the pillbox beam former. The three horns correspond to three independent beams and allow beam steering by switching from one feed to another. The proposed metasurface antenna is planar and extremely low-profile, thus suitable for small platforms such as CubeSats/SmallSats. A prototype validates the concept demonstrating a directivity as high as 31.9 dBi and a reflection coefficient lower than -15 dB at 94 GHz.
1 March 2021 in IEEE Transactions on Terahertz Science and Technology
In this paper, we propose a hybrid electro-mechanical scanning lens antenna array architecture suitable for the steering of highly directive beams at submillimeter wavelengths with field-of-views (FoV) of ±25°. The concept relies on combining electronic phase shifting of a sparse array with a mechanical translation of a lens array. The use of a sparse phased array significantly simplifies the RF front-end (number of active components, routing, thermal problems), while the translation of a lens array steers the element patterns to angles off-broadside, reducing the impact of grating lobes over a wide FoV. The mechanical translation required for the lens array is also significantly reduced compared to a single large lens, leading to faster and low-power mechanical implementation. In order to achieve wide bandwidth and large steering angles, a novel leaky wave lens feed concept is also implemented. A 550 GHz prototype was fabricated and measured demonstrating the scanning capabilities of the embedded element pattern and the radiation performance of the leaky wave fed antenna.