The issue of electronic heat dissipation has received much attention in recent times and has become one of the key factors in electronic components such as circuit boards. Therefore, designing of materials with good thermal conductivity is vital. In this work, a thermally conductive SBP/PU composite was prepared wherein the spherical h-BN@PMMA (SBP) composite powders were dispersed in the polyurethane (PU) matrix. The thermal conductivity of SBP was found to be significantly higher than that of the pure h-BN/PU composite at the same h-BN filler loading. The SBP/PU composite can reach a high thermal conductivity of 7.3 Wm⁻¹ K⁻¹ which is twice as high as that of pure h-BN/PU composite without surface treatment in the same condition. This enhancement in the property can be attributed to the uniform dispersion of SBP in the PU polymer matrix that leads to a three-dimensional continuous heat conduction thereby improving the heat diffusion of the entire composite. Hence, we provide a valuable method for preparing a 3-dimensional heat flow path in polyurethane composite, leading to a high thermal conductivity with a small amount of filler.

Recently, the use of fused deposition modeling (FDM) in the three-dimensional (3D) printing of thermal interface materials (TIMs) has garnered increasing attention. Because fillers orient themselves along the direction of the melt flow during printing, this method could effectively enhance the thermal conductivity of existing composite materials. However, the poor compatibility and intensive aggregation of h-BN fillers in polymer composites are still detrimental to their practical application in thermally conductive materials. In this study, hydroxyl-functionalized boron nitride (OH-BN) particles were prepared by chemical modification and ultrasonic-assisted liquid-phase exfoliation to explore their impact on the surface compatibility, mechanical properties and the final anisotropic thermal conductivity of thermoplastic polyurethane (TPU) composites fabricated by FDM printing. The results show that the surface-functionalized OH-BN fillers are homogeneously dispersed in the TPU matrix via hydrogen bonding interactions, which improve the interfacial adhesion between the filler and matrix. For the same concentration of loaded filler, the OH-BN/TPU composites exhibit better mechanical properties and thermal conductivities than composites incorporating non-modified h-BN. These composites also show higher heat conduction along the stand-vertical direction, while simultaneously exhibiting a low dielectric constant and dielectric loss. This work therefore provides a possible strategy for the fabrication of thermal management polymers using 3D-printing methods.

Thermal management has become one of the crucial factors in designing electronic equipment and therefore creating composites with high thermal conductivity is necessary. In this work, a new insight on hybrid filler strategy is proposed to enhance the thermal conductivity in Thermoplastic polyurethanes (TPU). Firstly, spherical aluminium oxide/hexagonal boron nitride (ABN) functional hybrid fillers are synthesized by the spray drying process. Then, ABN/TPU thermally conductive composite material is produced by melt mixing and hot pressing. Then, ABN/TPU thermally conductive composite material is produced by melt mixing and hot pressing. Our results demonstrate that the incorporation of spherical hybrid ABN filler assists in the formation of a three-dimensional continuous heat conduction structure that enhances the thermal conductivity of the neat thermoplastic TPU matrix. Hence, we present a valuable method for preparing the thermal interface materials (TIMs) with high thermal conductivity, and this method can also be applied to large-scale manufacturing.

In this study, different diameters of photoresist AZ4620 are defined using lithography. According to the specification of the back light module (BLM) for a liquid crystal display (LCD), the diameters of micro-lenses are divided into two groups. The first group includes lenses with diameters of 90, 95, 100, 105, 110 and 150 µm at a 100 µm pitch; the reflow temperatures for this first group range from 175–300°C with heating times of 6–24 h. The second group includes lenses with diameters of 10, 20, 30, 40, and 50 µm at pitches of 40, 30, 20, 10, and 25 µm, respectively; the reflow temperatures are the same as for the first group with heating times of 1–12 h. In this study, the parametric effects of reflow time and temperature on micro-opticals are characterized and discussed, and optical properties such as the focal length of micro-lenses are measured and analyzed. Then, each micro-lens is sputtered with a conductive seed layer of silver (Ag) for the subsequent eletroforming process, which is the mold for hot embossing. The mold is further incorporated with hot embossing materials and hot embossing techniques to produce the micro-lens required.