With the movement of the construction industry towards Construction 5.0, Digital Twin (DT) has emerged in recent years as a pivotal and comprehensive management tool for predictive strategies for infrastructure assets. However, its effective adoption and conceptual implementation remain limited in this domain. Current review works focused on applications and potentials of DT in general infrastructures. This review focuses on interpreting DT’s conceptual foundation in the flexible pavement asset context, including core components, considerations, and methodologies. Existing pavement DT implementations are evaluated to uncover their strengths, limitations, and potential for improvement. Based on a systematic review, this study proposes a comprehensive cognitive DT framework for pavement management. It explores the extent of enhanced decision-making and a large-scale collaborative DT environment. This study also identifies current and emerging challenges and enablers, as well as highlights future research directions to advance DT implementation and support its alignment with the transformative goals of Construction 5.0.
Highly localized stresses generated at the gauge corner of the outer rail cause fatigue cracking. The longitudinal bending stresses in the rail underhead radius position are of special interest, as tension spikes have been identified at this location during in-track measurements under high axle load conditions. The tension spike is a result of vertical and lateral head bending on the web. This effect is highly localized and is additional to the stresses generated due to vertical and lateral bending of the whole rail profile (the so-called global bending). This study examined contact and bending stresses by modelling the rail on a discrete foundation using finite elements and by considering the loading to be a fully slipping elliptical Hertzian contact patch. The analysis revealed that the tensile longitudinal stress was highly dependent on several service conditions: the contact patch offset from the rail centreline, the ratio of lateral (L) to vertical (V) loads, the direction of lateral traction, foundation stiffness and seasonal temperature variations. The tension spike increases, and the depth below the contact surface at which the stresses become tensile reduces, as the contact patch offset and/or the L/V ratio increases. Both these enhance the tendency for rolling contact fatigue cracks to turn downwards and become transverse defects. This is because an increase in tensile bending stresses together with both residual and thermally induced stresses can facilitate cracks to turn perpendicular to the tensile stresses once they reach a critical length. Shear traction towards the gauge corner was found to be the most damaging phenomenon.
31 July 2014 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
This paper investigated the effect of rail head wear (HW) and lateral forces on underhead radius stress conditions and resulting stress intensity factors (SIFs) of a long transverse crack. The occurrence of tension spikes at the underhead radius of the rail as a result of localised vertical and lateral bending of the head-on-web was significantly exacerbated with increasing rail HW. The extended finite element method (X-FEM) modelling, which had previously been validated by comparison with in-track measurements to verify the prediction of tension spikes, was used to model a single rail on discrete elastic foundations. SIFs along the crack front were parametrically evaluated in terms of changes in the contact patch offset (CPO), the (L/V) ratio of lateral (L) to vertical (V) loads, the rail HW, and crack size and shape. The X-FEM results revealed that for a long transverse crack, extending the crack length to the underhead radius position results in higher SIFs across the underhead radius as a result of tensile bending stresses. These higher SIFs can contribute to a massively higher crack growth rate at this location, as was evidenced by the crack growth morphology at the underhead radius.
An evaluation of the potential risk of fatigue damage at the rail underhead radius (UHR) due to the occurrence of a short duration tensile stress peak, as a wheel passes over, has been examined. The tensile stress peak is mainly due to the localised bending of the rail head-on-web and its magnitude is associated with the contact position, lateral and vertical forces and rail head wear (HW). The stresses at the underhead radius have been explored using the finite element method (FEM). The Dang Van (DV) criterion, implemented as a customised computer programme, was used to identify the fatigue damage at the UHR. Fatigue behaviour under heavy haul conditions was compared for heat-treated low alloy, euctectoid and hypereutectoid rail grades in order to predict allowable rail head wear limits.