Maria Virginia Gelfuso

Dr. Maria Virginia Gelfuso

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 October 2015 in Materials Research
Verified
Journal Article
Open access
PDF file
RBRicardo Mello Di Benedetto
Ricardo Mello Di Benedetto
MGMaria Virginia Gelfuso
Maria Virginia Gelfuso
DTDaniel Thomazini
Daniel Thomazini
Surface treatments done in banana fibers (BFs) can generate significant superficial structural changes enabling the production of mechanically stronger composites. In this way, the objective of this study was to evaluate the physicochemical and mechanical properties of banana fibers of Prata specie from inner and outer leaf sheaths, when irradiated with UV light (λmax = 400 nm) during 7 (UV7) and 15 (UV15) days. Structural and microstructural characterizations for non- and irradiated fibers were performed by, FT-IR spectroscopy and Scanning Electron Microscopy (SEM), which showed the influence of UV irradiation on BFs surface and chemical structure. The Ea involved in the thermal degradation process of InNatura fiber (188.2 kJ.mol–1) was obtained using Differential Thermal Analysis (DTA/TG). The results obtained from mechanical characterization showed that the UV7 fibers presented significant improvement in tensile strength (89.77 MPa) and elastic modulus (238.94 MPa) as compared to tensile strength (69.99 MPa) and elastic modulus (87.40 MPa) of InNatura fibers. Statistical analysis using two-way ANOVA has showed that there were no differences between mechanical properties of BFs from inner to outer leaf sheaths. UV radiation has proved to be a clean method for BF surface treatment, which can improve the mechanical properties of composites based on these fibers.

1 January 2020 in Materials Research
Verified
Journal Article
Open access
PDF file
STSamanta de O. A. Torres
Samanta de O. A. Torres
DTDaniel Thomazini
Daniel Thomazini
GBGabriel P. Balthazar
Gabriel P. Balthazar
MGMaria Virginia Gelfuso
Maria Virginia Gelfuso
Thermoelectric properties of pure polycrystalline CaMnO3 ceramics were significantly enhanced by increasing sintering holding time from 1 to 24 h. The Seebeck coefficient values were reduced while the sintering holding time was increased, and the DC electrical conductivity was enhanced from 255 S/m to 1.748 S/m. This same effect was observed in electronic thermal conductivity, increasing from 5x10-3 to 3.5x10-2W/m K, whereas the lattice thermal conductivity decreased from 5.0 to 4.0 W/m K at 873K. Overall, CaMnO3 ceramic sintered for 24 h demonstrated the best performance, which presented a Figure-of-Merit value of about 0.03. The grain size of the samples ranged from 2.79 µm to 6.45 µm, due to the sintering holding time, directly influencing the high-temperature thermoelectric properties of CaMnO3 ceramics.

13 February 2023 in Ceramics International
Verified
Journal Article
Closed access
LHL.S. Hagy
L.S. Hagy
KRK. Ramos
K. Ramos
MGMaria Virginia Gelfuso
Maria Virginia Gelfuso
ACA.L. Chinelatto
A.L. Chinelatto
ACA.S.A. Chinelatto
A.S.A. Chinelatto

7 February 2014 in International Journal of Applied Ceramic Technology
Verified
Journal Article
Closed access
PDF file
DTDaniel Thomazini
Daniel Thomazini
MGMaria Virginia Gelfuso
Maria Virginia Gelfuso
GVGabriela Maira Sanches Volpi
Gabriela Maira Sanches Volpi
JEJosé Antonio Eiras
José Antonio Eiras

1 March 2011 in Cerâmica
Verified
Journal Article
Open access
PDF file
DTD. Thomazini
D. Thomazini
MGMaria Virginia Gelfuso
Maria Virginia Gelfuso
ACA. S. A. Chinelatto
A. S. A. Chinelatto
FSF. K. Sanson
F. K. Sanson
FNF. Teixeira Neto
F. Teixeira Neto
It is well known that the heating mechanism and powder precursor define the microstructural characteristics of ceramics. Especially abnormal grain growth of pure alumina ceramics developed during conventional sintering method suggests that this material is a potential candidate to be treated in microwave sintering process. Alumina ceramics produced with commercial (A1K) and chemically synthesized powders were sintered in conventional and microwave furnaces. Two methods were employed to prepare the chemically synthesized nanosized powders: Pechini method and emulsification with oleic acid. The microwave sintered samples were characterized by apparent density and scanning electron microscopy and compared with the samples sintered in a conventional furnace. Alumina ceramics sintered in the microwave furnace had fine grained microstructure, not related with the starting powders. This characteristic was achieved in a sintering time shorter than those produced in the conventional furnace. However, satisfactory densification was observed only to A1K ceramics (3.95 g/cm³) sintered during one hour in microwave furnace.

17 November 2018 in International Journal of Applied Ceramic Technology
Verified
Journal Article
Closed access
PDF file
MGMaria Virginia Gelfuso
Maria Virginia Gelfuso
JUJuan Oswaldo Montoya Uribe
Juan Oswaldo Montoya Uribe
DTDaniel Thomazini
Daniel Thomazini