In this paper, a model for Cr (VI) removal and optimization was made using a novel aerogel material, chitosan-resole CS/R aerogel, where a freeze-drying and final thermal treatment was employed to fabricate the aerogel. This processing ensures a network structure and stability for the CS, despite the non-uniform ice growth promoted by this process. Morphological analysis indicated a successful aerogel elaboration process., FTIR spectroscopy corroborated the aerogel precursor’s identity and ascertained chemical bonding after adsorption. Owing to the variability of formulations, the adsorption capacity was modeled and optimized using computational techniques. The response surface methodology (RSM), based on the Box–Behnken design using three levels, was used to calculate the best control parameters for the CS/R aerogel: the concentration at %vol (50–90%), the initial concentration of Cr (VI) (25–100 mg/L), and adsorption time (0.3–4 h). Analysis of variance (ANOVA) and 3D graphs reveal that the CS/R aerogel concentration and adsorption time are the main parameters that influence the initial concentration of CS/R aerogel metal-ion uptake. The developed model successfully describes the process with a correlation coefficient of R2 = 0.96 for the RSM. The model obtained was optimized to find the best material design proposal for Cr (VI) removal. Numerical optimization was used and showed superior Cr (VI) removal (94.4%) under conditions of a CS/R aerogel concentration of 87/13 %vol, with an initial concentration of Cr (VI) of 31 mg/L, and an adsorption time of 3.02 h. These results suggest that the proposed computational model can obtain an effective and viable model for CS material processing and for optimization of the uptake of this metal.
Hydrogen is ideal for replacing fossil fuels because upon combustion it generates only water. Dark fermentation (DF) from lignocellulose might be a competitive process for hydrogen production at the industrial scale. However, lignocellulose must be pretreated to obtain fermentable sugars, which is costly and creates pollution. Microorganisms from bovine rumen efficiently degrade lignocellulose. Unfortunately, they have scarcely been explored for the production of hydrogen. Therefore, deeper studies on the culture conditions have to be undertaken to understand the behavior of microbial consortia from the rumen of bovines (MCRB) during hydrogen production. In this work, we evaluated the production of hydrogen by DF with MCRB by varying the incubation time, two culture media (MB and Rhodospirillaceae), headspace (40 and 80 mL), and thermal treatment. It was found that the production of hydrogen was maximum at 16 h MCRB incubation in MB. An amount of 80 mL headspace resulted in a threefold production of hydrogen as compared to 40 mL; the MCRB without heat treatment had a higher H2 yield. The production of hydrogen with 32 MCRB was highly variable, ranging between 21 and 696 mL. Our findings show a different perspective on the treatment of MCRB for the production of hydrogen and give insights on the impact of the culture conditions for increasing hydrogen production.
Aligned CS/Rx aerogels were fabricated by inducing non-directional ice growth (freeze-molding) followed by low-temperature curing, resulting in monoliths with interconnected channels, a high void fraction, and moldability. The swelling index (S%) was calculated to be 1029, the apparent density 0.496 g·cm−3, and the estimated porosity 90% based on micrographic analysis. Aerogels have mechanical behavior Shore A hardness greater than 25. Batch metal removal tests were performed (10 mL, 100 mg·L−1 Cr(VI), 0.19 g adsorbent, 24 h, and pH 5–5.5), and the material achieved 95% metal removal. Additional kinetic and isothermal results were obtained using CS85R15 on a packed column (20 to 140 mg·L−1, 1000 mL Cr(VI), 0.80 g adsorbent, 24 h, and pH 5–5.5). Equilibrium data were consistent with a heterogeneous surface hosting a specific site, as reflected in the joint Freundlich/Langmuir fit (qmax 100.8 mg·g−1 for Langmuir). This confirmed the preservation of chitosan functionalities (–OH/–NH) after processing, while XPS detected chromium on the surface with signals consistent with the partial reduction of Cr(VI) to Cr(III) on the aerogel surface. This highlights the relevance of adsorption-based technologies for water remediation, where high-porosity and low-density materials allow for short diffusion pathways and capture electrostatics by protonated amines and redox conversion of hazardous substances. The soft-cure freeze-molding technique is simple, scalable, and compatible with packed-bed/column operation, providing a material platform for tailoring the microstructure (sheets and channels) and surface chemistry to regenerable sorbents for industrial wastewater treatment.
3 October 2026 in Journal of Polymers and the Environment