Rui Gao

Dr. Rui Gao

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 March 2025 in Tribology International
Verified
Journal Article
Closed access
RGRui Gao
Rui Gao
YLYee Man Loh
Yee Man Loh
KLKangsen Li
Kangsen Li
RCRui Chen
Rui Chen
CJChen Jiang
Chen Jiang
Chunjin WangChunjin Wang
Chunjin Wang

19 May 2023 in Ceramics International
Verified
Journal Article
Closed access
YLYee Man Loh
Yee Man Loh
RGRui Gao
Rui Gao
Chi Fai CheungChi Fai Cheung
Chi Fai Cheung
YCYanning Chen
Yanning Chen
XLXin Li
Xin Li
Chunjin WangChunjin Wang
Chunjin Wang

24 July 2025 in International Journal of Mechanical Sciences
Verified
Journal Article
Closed access
QZQingzheng Zhang
Qingzheng Zhang
RGRui Gao
Rui Gao
CJChen Jiang
Chen Jiang
ZZZejin Zhan
Zejin Zhan
QZQixian Zhang
Qixian Zhang
Chunjin WangChunjin Wang
Chunjin Wang

12 December 2024 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
RGRui Gao
Rui Gao
DLDawei Luo
Dawei Luo
YLYee Man Loh
Yee Man Loh
Chi Fai CheungChi Fai Cheung
Chi Fai Cheung
CJChen Jiang
Chen Jiang
Chunjin WangChunjin Wang
Chunjin Wang

11 October 2021 in Semiconductor Science and Technology
Verified
Journal Article
Closed access
RGRui Gao
Rui Gao
CJChen Jiang
Chen Jiang
XLXiaoHu Lang
XiaoHu Lang
PHPengHui Huang
PengHui Huang
JJJinXin Jiang
JinXin Jiang
High performance and low energy consumption are major priorities for modern manufacturing techniques. In order to improve the quality of cleavage planes while reducing energy consumption, this paper presents an experimental investigation of energy savings during the mechanical cleavage process using different scratching methods. According to the simulation results, an improved scratching method, dot scratching, gave a scratching length of approximately 0.6 mm. The scratching energies of the traditional scratching method and the dot scratching method along the and directions were calculated and analysed from the perspective of energy consumption. A series of scratching and cleavage experiments were carried out to investigate the features on scratch and cleavage surfaces. The experimental results for the scratching procedure showed that scratching along the direction using the dot scratching method is beneficial for reducing the maximum damage width of gallium arsenide (GaAs). The dot scratching method can significantly reduce energy consumption during the cleavage of GaAs, and the energy saving ratios exceed 70%. A flat cleavage plane can be obtained by cleavage using the dot scratching method under a lower scratching load. Adoption of the dot scratching method thus has the potential to improve the efficiency and quality of cleavage processes and offers a practical solution for the greener manufacturing of semiconductor cleavage planes.

30 August 2022 in IEEE Transactions on Semiconductor Manufacturing
Verified
Journal Article
Closed access
RGRui Gao
Rui Gao
CJChen Jiang
Chen Jiang
XLXiaohu Lang
Xiaohu Lang
ZZZexi Zheng
Zexi Zheng
JJJinxin Jiang
Jinxin Jiang
PHPenghui Huang
Penghui Huang
To satisfy the increasing requirements for highquality cavity mirrors for semiconductor lasers, the influence of the anisotropic stress field generated by scratching GaAs on the quality of cleavage planes was investigated. First, a novel method for calculating the interplanar spacing was proposed to estimate the favourable direction for the scratching operation. Some mechanical properties in the scratching direction were calculated. Consequently, an anisotropic calculation model of the stress field generated by scratching was established. The calculation model was used to analyse the y-component stress field distribution along different directions beneath the indenter. The results show that the maximum stress occurs at the contact area between the material and indenter tip, and the stress along the orientation is lower than that along the orientation. According to our experiments, a significant decrease in the average radial crack length and a slight decrease in the average kerf width were observed along the 011 direction compared to the corresponding results for the 001 direction. In addition, the (011) plane had a surface roughness of 0.43 nm and could become a preferential cleavage plane under a low scratching load. The results of this study contribute to advance our understanding of the mechanisms of mechanical cleavage processes.