The climate crisis represents one of the greatest contemporary global challenges, requiring actions to mitigate its impacts and sustainable solutions to meet the growing demands for clean energy and coastal protection. Therefore, the study of devices such as the submerged plate (SP), which simultaneously acts as a breakwater (BW) and wave energy converter (WEC), is especially relevant. In this context, the present numerical study compares the efficiency of an SP device under regular waves across different geometric configurations considering inclination angles. To achieve this, a horizontal SP was adopted as a reference. Its thickness and total material volume were kept constant while ten alternative geometries, each with a different inclination for the SP, were proposed and investigated. The computational domain was modeled as a full-scale regular wave channel with each SP positioned below the free surface. The volume of fluid (VOF) multiphase model was employed to represent the interaction between water and air. The finite volume method (FVM) was applied to solve the transport equations for volume fraction, momentum, and mass. The SP’s efficiency as a BW was evaluated by assessing the free surface elevation upstream and downstream of the SP, while its efficiency as a WEC was measured by evaluating the axial velocity below the SP. Results indicated that the efficiency of the SP can vary significantly depending on its inclination, with the optimal case at θ = 15° showing improvements of 11.95% and 16.59%, respectively, as BW and WEC.
The present work investigated numerically turbulent airflows over a hybrid Darrieus/Savonius vertical axis wind turbine. Firstly, the isolated turbines were validated in comparison to previous studies from the literature. Later, new recommendations were obtained for the simulation of a hybrid turbine subject to turbulent airflow. The numerical simulations consisted of the solution of time-averaged equations of mass and momentum in x and y directions using the finite volume method, available in the commercial code Ansys Fluent (version 2022 R1). For closure of turbulence, the k − ω SST (Shear Stress Transport) model was employed. For lower magnitudes of tip speed ratio (TSR), the hybrid turbine improved the power coefficient (CP) compared to the Darrieus turbine (e.g., by 70% at TSR = 0.75), thereby demonstrating the self-starting capability of the hybrid configuration. Unexpectedly, at the optimal TSR = 1.5, the hybrid turbine performed about 6.5% better than the Darrieus turbine, indicating that the balance between the additional power generated by the Savonius rotor and losses caused by flow disturbances in the hybrid configuration was positive. As a novelty, results highlighted the role of each rotor (Darrieus and Savonius) for the performance of the hybrid turbine by comparing it with isolated Darrieus and Savonius turbines under the same conditions.
This study investigates the influence of inclination on a submerged plate (SP) device acting as both a breakwater (BW) and a wave energy converter (WEC) subjected to representative regular and realistic irregular waves of a sea state across 11 inclination angles. Numerical simulations were conducted using ANSYS Fluent. Regular waves were generated by Stokes’s second-order theory, while the WaveMIMO technique was employed to generate irregular waves. Using the volume of fluid (VOF) method to model the water–air interaction, both approaches generate waves by imposing their vertical and horizontal velocity components at the inlet of the wave flume. The SP’s performance as a BW was analyzed based on the upstream and downstream free surface elevations of the device; in turn, its performance as a WEC was determined through its axial velocity beneath the plate. The results indicate that performance varies between regular and irregular wave conditions, underscoring the importance of accurately characterizing the sea state at the intended installation site. These findings demonstrate that the inclination of the SP plays a critical role in balancing its dual functionality, with certain configurations enhancing WEC efficiency by over 50% while still offering relevant BW performance, even under realistic irregular sea conditions.
O presente trabalho consiste na construção de um modelo numérico de um escoamento turbulento, permanente, bidimensional, incompressível e com convecção forçada ao longo de um micro canal com paredes com corrugações em formato trapezoidal. O caso é simulado para escoamentos convectivos com números de Reynolds e Prandtl iguais a ReD = 22.000 e Pr = 0,71. As equações temporais médias de conservação de massa, quantidade de movimento e energia são resolvidas através do Método dos Volumes Finitos implementado no software Ansys Fluent. A abordagem RANS (Reynolds Averaged Navier-Stokes) com modelo k - ω SST (Shear Stress Transport) é empregada na modelagem da turbulência. Ao final do estudo foi possível obter um modelo numérico capaz de predizer o escoamento em micro canais com corrugações trapezoidais. Além disso, se observou que a direção da corrugação tem influência direta na perda de carga e troca térmica. As corrugações que estão direcionadas para fora do domínio não contribuem para a troca térmica, mas sim para a perda de carga. Enquanto as corrugações voltadas internamente para o domínio são as que mais contribuem para a troca térmica.
8 April 2026 in Revista Mundi Engenharia, Tecnologia e Gestão (ISSN: 2525-4782)
O presente estudo numérico tem como objetivo determinar a disposição ótima de aletas inseridas de forma alternada em microcanais, a fim de conduzir a máxima taxa de transferência de calor e a mínima perda de carga no canal. O escoamento no canal é de ar em menor temperatura, laminar, incompressível e em regime permanente, com transferência de calor por convecção forçada. O método design construtal é usado para o desenvolvimento das alternativas de projeto e o método TOPSIS é utilizado para avaliar os resultados de forma multiobjetiva, a partir de um indicador de performance multiobjetivo (Ci), baseado em uma ponderação de pesos para variável térmica e fluidodinâmica. No presente estudo são investigadas as razões entre as distâncias das aletas 1 e 2 e o comprimento da área de ocupação (L1/L e L2/L), enquanto as aletas 0 e 3 são mantidas fixas (L0/L = 0,125 e L3/L = 0,875). Todas as simulações numéricas foram conduzidas considerando um escoamento de ar com números de Reynolds e Prandtl constantes, ReH = 100 e Pr = 0,71, respectivamente. Os resultados indicaram que, ao atribuir um peso de 50% para cada indicador de desempenho, a geometria que apresenta os maiores valores de Ci possui configuração assimétrica com distância entre aletas não uniforme.