The unprecedented development of perovskite-silicon (PSC-Si) tandem solar cells in the last five years has been hindered by several challenges towards industrialization, which require further research. The combination of the low cost of perovskite and legacy silicon solar cells serve as primary drivers for PSC-Si tandem solar cell improvement. For the perovskite top-cell, the utmost concern reported in the literature is perovskite instability. Hence, proposed physical loss mechanisms for intrinsic and extrinsic instability as triggering mechanisms for hysteresis, ion segregation, and trap states, along with the latest proposed mitigation strategies in terms of stability engineering, are discussed. The silicon bottom cell, being a mature technology, is currently facing bottleneck challenges to achieve power conversion efficiencies (PCE) greater than 26.7%, which requires more understanding in the context of light management and passivation technologies. Finally, for large-scale industrialization of the PSC-Si tandem solar cell, the promising silicon wafer thinning, and large-scale film deposition technologies could cause a shift and align with a more affordable and flexible roll-to-roll PSC-Si technology. Therefore, this review aims to provide deliberate guidance on critical fundamental issues and configuration factors in current PSC-Si tandem technologies towards large-scale industrialization. to meet the 2031 PSC-Si Tandem road maps market target.
Organic-inorganic lead halide perovskites have significant role in the photovoltaic (PV) technology due to its high efficiency, lightweight and cost effectiveness especially methyl ammonium lead (II) iodide (MALI). The MALI can act as absorber layer which has a band gap of 1.5 eV which is compatible to be paired with silicon (Si) solar cell with energy gap of 1.124 eV as a tandem solar cell. This tandem approach is an refined solution to improve the efficiency of Si solar cell that has been stuck around 25 % for 15 years. This study focuses on the development of the device configuration model for Si-perovskite tandem solar cell by using SCAPS simulation. The thickness and dopant concentration of perovskite layer have affected the solar cell parameters performance. The efficiency result obtained from SCAPS simulation is 27.29 % for Si-perovskite tandem solar cell with an open circuit voltage of 0.8178 V, short circuit current 43.55 mA/cm2 and fill factor 76.61 %.
High-performance electron transport layer (ETL) anode generally needs to form a uniform dense layer with suitable conduction band position and good electron transport properties. The TiO2 photoanode is primarily applied as the ETL because it is low-cost, has diverse thin-film preparation methods and has good chemical stability. However, pure TiO2 is not an ideal ETL because it lacks several important criteria, such as low conductivity and conduction band mismatch with compositional-tailored perovskite. Thus, TiO2 is an inefficient photo-anode or ETL for high-performance perovskite devices. In this study, sulfur as dopant in the TiO2 photo-anode thin film is used to fabricate solid-state planar perovskite solar cells in relatively high humidity (40–50%). The deposited S-doped thin film improves the power conversion efficiency (PCE) of the device to 6.0%, with the un-doped TiO2 producing a PCE of 5.1% in the best device. Improvement in PCE is due to lower recombination and higher photocurrent density, resulting in 18% increase in PCE (5.1–6.0%).
18 February 2017 in Materials for Renewable and Sustainable Energy
Dye-sensitized solar cells (DSSCs) are fabricated using natural sensitizers extracted from rengas (Gluta spp.) and mengkulang (Heritieraelata) wood. The natural sensitizers are extracted using a cold extraction and the Soxhlet extraction methods. This paper presents the results of the analysis of the optical characteristics of the sensitizers via ultraviolet–visible spectrophotometry and Fourier transform infrared spectroscopy. The optical band gap and the highest occupied molecular orbital (HOMO)–lowest unoccupied molecular orbital (LUMO) levels of each investigated sensitizer are calculated on the basis of the analyzed data collected from photoluminescence and cyclic voltammetry. The DSSCs with the mengkulang sensitizer have better conversion efficiency (ŋ = 0.1695%) than the DSSCs with the rengas sensitizer (ŋ = 0.109%). The performance of the DSSCs indicates an increment as the ratios of the mixed mengkulang:rengas (60%:40%) and mengkulang:rengas (40%:60%) sensitizers increase up to 0.296 and 0.292%, respectively.