The application of the hyperelasticity constitutive relationships for modelling of elastomeric bridge bearings is presented. Elastomers which are used for bridge bearings are nearly incompressible materials. Consequently, two models of hyperelasticity for rubber-like materials, i.e. neo-Hookean and Yeoh models are considered. The neo-Hookean model is the simplest possible model of hyperelasticity but unfortunately it has a number of disadvantages (i.e. at certain deformation modes it gives physically unreasonable predictions). The Yeoh model for nonlinear elastic materials is superior to neo-Hookean model and leads to rational description of the behavior of the elastomers for significant elongations and is implemented in many commercial programs using finite element method (FEM). In this work, ABAQUS program is utilized for modelling of chosen bridge bearings. The parameters of two constitutive models are determined based on experimental results and are used in numerical calculations for selected examples of bridge bearings. Concluding remarks are drawn and directions of future research are outlined
17 June 2021 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
In this work a number of selected, isotropic, invariant-based hyperelastic models are analyzed. The considered constitutive relations of hyperelasticity include the model by Gent (G) and its extension, the so-called generalized Gent model (GG), the exponential-power law model (Exp-PL) and the power law model (PL). The material parameters of the models under study have been identified for eight different experimental data sets. As it has been demonstrated, the much celebrated Gent’s model does not always allow to obtain an acceptable quality of the experimental data approximation. Furthermore, it is observed that the best curve fitting quality is usually achieved when the experimentally derived conditions that were proposed by Rivlin and Saunders are fulfilled. However, it is shown that the conditions by Rivlin and Saunders are in a contradiction with the mathematical requirements of stored energy polyconvexity. A polyconvex stored energy function is assumed in order to ensure the existence of solutions to a properly defined boundary value problem and to avoid non-physical material response. It is found that in the case of the analyzed hyperelastic models the application of polyconvexity conditions leads to only a slight decrease in the curve fitting quality. When the energy polyconvexity is assumed, the best experimental data approximation is usually obtained for the PL model. Among the non-polyconvex hyperelastic models, the best curve fitting results are most frequently achieved for the GG model. However, it is shown that both the G and the GG models are problematic due to the presence of the locking effect.
The paper presents a study of the propagation and interaction of weakly nonlinear plane waves in isotropic and transversely isotropic media. It begins with a definition of stored energy functions of considered hyperelastic models. The equation of elastodynamics as well as the first-order quasilinear hyperbolic system for plane waves are provided. The eigensystem for this system is determined to study three-wave interaction coefficients. The main part of the paper concerns a discussion of these coefficients. Applying the weakly nonlinear asymptotics method, it is shown that in the case of transverse isotropy the inviscid Burgers’ equation describes an evolution of a single quasi-shear wave. The result contradicts the case of isotropy, where the equation with quadratic nonlinearity cannot describe any shear wave propagation. The paper ends with an example of numerical solutions for the obtained evolution equation.
14 February 2014 in Road Materials and Pavement Design
A theoretical model for an elastic anisotropic composite of road mixtures reinforced with grids together with its isotropic approximation is proposed. In the considered models, some elements of the mechanics of fibrous composite materials and optimisation theory are used. A composite model is an energy model; that is, constitutive relationships result from the differentiation of the stored energy function arising from two summed parts corresponding to the matrix and reinforcement grid energy via mixture theory. The obtained model is incorporated into the commercial finite element program ABAQUS via a user subroutine written in Fortran. The correctness of the proposed composite constitutive model has been tested by a numerical solution (with the application of a finite element program) of the structure, in which the matrix is modelled as a three-dimensional continuum region and the reinforcement as working in one dimension a set of truss elements. In addition, in the paper the proposition of approximation of the composite orthotropic model with an isotropic one is presented. The interpretation and application of this approximation are analysed. The energetically equivalent isotropic model for the layer with grid reinforcement can be directly used in standard programs used for designing road pavements with mechanistic methods.