Ignaz Eisele

Prof. Dr. Ignaz Eisele


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 May 2018 in Sensors
Verified
Journal Article
Open access
PDF file
Jamila BoudadenJamila Boudaden
Jamila Boudaden
MSMatthias Steinmaßl
Matthias Steinmaßl
HEHanns-Erik Endres
Hanns-Erik Endres
ADAndreas Drost
Andreas Drost
IEIgnaz Eisele
Ignaz Eisele
Peter Muller-BuschbaumPeter Muller-Buschbaum
Peter Muller-Buschbaum
The development of humidity sensors with simple transduction principles attracts considerable interest by both scientific researchers and industrial companies. Capacitive humidity sensors, based on polyimide sensing material with different thickness and surface morphologies, are prepared. The surface morphology of the sensing layer is varied from flat to rough and then to nanostructure called nanograss by using an oxygen plasma etch process. The relative humidity (RH) sensor selectively responds to the presence of water vapor by a capacitance change. The interaction between polyimide and water molecules is studied by FTIR spectroscopy. The complete characterization of the prepared capacitive humidity sensor performance is realized using a gas mixing setup and an evaluation kit. A linear correlation is found between the measured capacitance and the RH level in the range of 5 to 85%. The morphology of the humidity sensing layer is revealed as an important parameter influencing the sensor performance. It is proved that a nanograss-like structure is the most effective for detecting RH, due to its rapid response and recovery times, which are comparable to or even better than the ones of commercial polymer-based sensors. This work demonstrates the readiness of the developed RH sensor technology for industrialization.

23 May 2018 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Jamila BoudadenJamila Boudaden
Jamila Boudaden
SAStephan Altmannshofer
Stephan Altmannshofer
RWRobert Wieland
Robert Wieland
MPMichael Pittroff
Michael Pittroff
IEIgnaz Eisele
Ignaz Eisele
The gases used in industrial cleaning processes are considered greenhouse gases with a high global warming potential (GWP). It is important to provide a viable alternative chemical vapor deposition (CVD) cleaning gas that is capable of removing efficiently deposited layers on the CVD chamber inner wall and other parts of the apparatus. The cleaning gas has to be environmental friendly in order to avoid accentuation of the global warming phenomena. Besides that, the alternative cleaning gas should be compatible with the existing gas delivery system and the CVD equipment that is already used by industrial companies. Only by fulfilling the three requirements mentioned above is it possible to replace the well-established cleaning gases. In this project, an F2–gas mixture for the in-situ cleaning of CVD chambers has been studied and compared with conventional cleaning methods. The conventional cleaning process is defined as a cleaning procedure using either C2F6 in RF plasma discharge or NF3 in remote plasma discharge.

31 July 2019 in Nanomaterials
Verified
Journal Article
Open access
PDF file
Jamila BoudadenJamila Boudaden
Jamila Boudaden
AKArmin Klumpp
Armin Klumpp
HEHanns-Erik Endres
Hanns-Erik Endres
IEIgnaz Eisele
Ignaz Eisele
Hybrid materials based on inorganic particles and an organic polymer were developed and used as an efficient sensing material for carbon dioxide (CO2). The sensing material consists of fumed silica that is functionalized with an organic polymer, polyethylenimine, by means of the impregnation method. The organic polymer is effectively immobilized around the silica nanoparticles and confirmed by infrared spectroscopy. Thermogravimetric analysis proves the thermal stability of the sensing material. CO2 capacitive sensors operating at temperatures lower than 70 °C were fabricated by depositing a thin layer of hybrid sensing material on interdigitated gold electrodes. Impedance spectroscopy explored the sensing capability of the hybrid organic–inorganic material towards CO2 in the presence of different relative humidity levels, as well as its stability and reversibility. This strategy to couple organic and inorganic materials as a sensing layer for CO2 paves the way for the design of a low-cost CO2 sensor.

8 January 2019 in Materials
Verified
Journal Article
Open access
PDF file
CBChristian Bscheid
Christian Bscheid
CEChristian Engst
Christian Engst
IEIgnaz Eisele
Ignaz Eisele
CKChristoph Kutter
Christoph Kutter
Contactless minority carrier lifetime (lifetime) measurements by means of microwave detected photoconductivity are employed for oxidation process characterization and furnace profiling. Characterization is performed on oxidized float zone substrates with high resistivity and outstanding bulk quality, suggesting that the measured effective lifetime is strongly dominated by interface recombination and therefore reflects the oxide quality. The applied approach requires neither test structures nor time consuming measurements and is therefore of particular interest if high throughput is required. The method is used to investigate the impact of oxidation furnace leakage as well as to analyze the oxidation homogeneity across a horizontal oxidation furnace. For comparison, capacitance-voltage measurements are conducted to characterize the oxide properties. It is found that any type of furnace leakage, which induces fixed oxide charges as well as interface states, has a heavy impact on the measured effective lifetime, especially on the shape of generation rate dependent lifetime curves. Furthermore, a distinct lifetime decrease towards the tube door of the oxidation furnace could be observed. The latter is even detectable in an ideal oxidation process, generating high quality oxides. Besides plain equipment characterization, the presented approach is suitable to optimize the oxidation process itself regarding different parameters like temperature, gas flow, pressure, or process time.

11 August 2017 in Proceedings
Verified
Conference Paper
Open access
PDF file
Jamila BoudadenJamila Boudaden
Jamila Boudaden
AKArmin Klumpp
Armin Klumpp
HEHanns-Erik Endres
Hanns-Erik Endres
IEIgnaz Eisele
Ignaz Eisele
The objective of the present paper is to provide a concept for a chemical sensor having a small size, a low power consumption and a high reliability for sensing CO2 under different humidity levels at atmospheric pressure, while maintaining a long term stability under working conditions. A high temperature regeneration process of the sensing layer is unneeded to ensure a long term stability of the sensing material. This objective is achieved by using a hybrid organic-inorganic nanomaterial, consisting of inorganic nanoparticles functionalized with an amine-based polymer.

17 January 2020 in Journal of Applied Physics
Verified
Journal Article
Open access
PDF file
CEChristian Engst
Christian Engst
IEIgnaz Eisele
Ignaz Eisele
CKChristoph Kutter
Christoph Kutter
Unannealed neutron transmutation doped silicon substrates with a target resistivity of approximately 1000 Ω cm are characterized for radiation induced defects by means of microwave detected photoinduced current transient spectroscopy (MD-PICTS). This technique is a contactless advancement of conventional PICTS and does not require the fabrication of ohmic contacts. Defect spectroscopy by means of MD-PICTS is conducted in a broad temperature range between 30 K and 293 K, which makes it possible to identify energetically shallow as well as deep traps. In addition, a wavelength dependent analysis is performed to determine whether a defect is located at the surface or in the bulk material. Three traps with an average activation energy of 68 meV , 85 meV , and 150 meV are observed. In addition, an indication for deep defect states with activation energies between 320 meV and 480 meV is found. According to the wavelength dependent analysis, it is assumed that all observed traps are bulk defects. Finally, a minority carrier lifetime of approximately 0.7 μs is determined, suggesting that the crystal is heavily damaged by neutron radiation.