Layered cathode materials of the type Na1+xLi0.05Mn0.54Co0.13NiyO2−z (0 < x < 0.1, y = 0.13 or 0.2, z < 0.1) were prepared by direct ion-exchange reactions, starting from Li1.2Mn0.54Co0.13Ni0.13O2 and Li1.13Mn0.54Co0.13Ni0.2O2. They were examined vs. Na foil or sodiated hard carbon anodes as high capacity positive electrode materials for Na ion batteries with an initial reversible capacity >200 mA h g−1. Analysis by X-ray and electron diffraction reveals that the new materials are initially mixtures of rhombohedral and monoclinic phases. Attempts to prepare layered compounds with similar compositions by chemical means resulted in phases of hexagonal structure with rather poor electrochemical activity, emphasizing the importance of the synthesis by electrochemical ion exchange. Also, the stability of electrochemically prepared Na insertion cathode materials in cycling experiments was insufficient for practical consideration. In turn, cathodes prepared from the same Li precursors coated by a thin layer of alumina via atomic layer deposition, followed by electrochemical Na/Li ion exchange, demonstrated stable capacity (>170 mA h g−1) during prolonged cycling. Their average discharge voltage was 300 mV higher compared to the counterpart uncoated Na intercalation cathodes. The structure and behavior of these electrodes were thoroughly explored by a variety of analytical and surface tools, in conjunction with electrochemical techniques.
1 November 2022 in Journal of the Electrochemical Society
The transference number for cations, t+ , is one of the most important parameters for characterizing polymeric and/or composite solid electrolytes. It expresses the contribution of the positive charge carriers to the total conductivity, which in turn reflects the degree of polarization due to the negative carriers in the electrolyte systems. Four electrochemical methods based on different equations commonly used for obtaining t+ are compared. A series of experiments were conducted with solid polymer electrolytes based on polyethylene oxide with and without TiO 2 ceramic additive. Interestingly, the oldest method developed and presented four decades ago, emerges as the most simple, reliable, sensitive, repeatable, and stable option for determining t+ values over time.
1 July 2022 in Journal of the Electrochemical Society
Solid-state batteries have received renewed attention in recent years. The present study compares all-solid-state sodium batteries containing sodium metal anodes, NaTi 2 (PO 4 ) 3 (NTP) cathodes and PEO polymer electrolyte (PE) with two salts—NaPF 6 and NaClO 4 . Electrochemical properties were determined by means of both AC and DC measurements. For fresh symmetric cells, it seems like using NaClO 4 as the salt leads to a lower interfacial resistance, but during contact with Na anodes, PEO:NaClO 4 PE produces an unstable interface whereas PEO-NaPF 6 forms a stable interface upon contact with sodium anodes. Battery prototypes with PEO:NaClO 4 showed a better performance than those using PEO:NaPF 6 in terms of specific capacity and energy content, as NaPF 6 produces HF by-product which impairs the performance of full cells. However, the use of composite solid electrolyte containing PEO:NaPF 6 and TiO 2 nanotubes alleviates detrimental effects of HF and thus enables a better performance of SS Na battery prototypes. This is probably due to the titania particles acting as a scavenger of HF, an inevitable contaminant in electrolyte systems containing PF 6− anions. On adding TiO 2 to polymer electrolytes, of both salts, the performance improves, what means that the TiO 2 has several positive effects in these systems.
High electrolyte-electrode interface stability is essential for solid state batteries to avoid side reactions that form interphases and voids, leading to loss of contact and increased impedance. Such detrimental situations increase overvoltage, reduce cycling efficiency, and shorten battery cycle life. While composite solid electrolytes were studied extensively, the effect of inorganic additives in the polymer matrix on the electrolyte-anode interface remains unclear. Here, solid electrolyte was studied for batteries with sodium metal anode based on polyethylene oxide (PEO) polymeric matrix containing ceramic additive. Extensive electrochemical analyses under both AC and DC conditions were performed, and chemical reactions between sodium metal and the PEO matrix, which produce interphases at the electrode-electrolyte interface, were investigated. Addition of sodium beta aluminate in the matrix appears to mitigate these reactions, removing a major obstacle on the way to effective all-solid-state rechargeable sodium batteries.
3 December 2024 in Journal of the Electrochemical Society
Developing polymer electrolytes as an alternative to aprotic liquid electrolytes for lithium and sodium-ion batteries aims to enhance their safety, durability, and cost. Among these, polyethylene oxide (PEO) is a favorite choice due to its wide availability, excellent versatility, and mechanical properties. PEO:NaTFSI and PEO:NaFSI are stable and efficient ion-conducting solid polymer electrolytes compared to other PEO:NaX matrices (for instance, X = [PF6]−, [ClO4]−). We tested Na/PEO:NaTFSI/NVP cells at low temperatures (40 °C) and carried out a series of electrochemical measurements to extract vital performance metrics such as diffusion coefficient, transference number, conductivity, and activation energy. Our findings emphasize the important role of the anions’ nature in the properties of polymeric electrolytes like those based on PEO, in which there are strong interactions between the ions and the oxygen atoms. Highly important are the interfacial interactions of the anions with the electrodes, which form surface species that determine stability and charge-transfer kinetics. Significant impact of TFSI anions on the cathode-electrolyte interfacial properties may explain the exceptional performance of sodium batteries at 40 °C, which is below the melting temperature of PEO. Our findings may open the door for an effective operation of solid-state batteries at room temperatures.