Gulnoz Khakimova Nigmanovna

Prof. Gulnoz Khakimova Nigmanovna


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 April 2024 in Bulletin of Science and Practice
Verified
Journal Article
Closed access
BUB. Uralov
B. Uralov
Nikolai Ivanovich VatinNikolai Ivanovich Vatin
Nikolai Ivanovich Vatin
GNGulnoz Khakimova Nigmanovna
Gulnoz Khakimova Nigmanovna
JKJ. Kayumov
J. Kayumov
SNS. Nishanova
S. Nishanova
DAD. Arzieva
D. Arzieva
The paper presents the results of a theoretical and experimental study of the wear rate of the elements of the flow part of centrifugal and axial pumps. Theoretical formulas recommended by various authors, obtained for models with flat samples based on energy theory, do not take into account the features of hydraulic machines. Considering the movement of solid particles in the inter-blade channels of the impellers of centrifugal and axial pumps, calculation schemes were chosen that correspond to the hydraulic and physical wear processes. The analysis shows that the influence of centrifugal and inertial forces in the inter-blade channel of the impellers of centrifugal and axial pumps causes separation and redistribution of solid particles in the flow. As a result, in centrifugal pumps in the end part of the blade and axial pumps in the end gap of the impeller, the local concentration of solid particles increases compared to the average. The work also provides dependencies for calculating the intensity of water-abrasive wear of pump working parts.

29 July 2026 in Preprints.org
Verified
Preprint
Open access
PDF file
Murodjon SamadiyMurodjon Samadiy
Murodjon Samadiy
Bakhodir AbdullayevBakhodir Abdullayev
Bakhodir Abdullayev
SUShavkat Umarov
Shavkat Umarov
MZMiyasar Zhumanova
Miyasar Zhumanova
GNGulnoz Khakimova Nigmanovna
Gulnoz Khakimova Nigmanovna
AUAzizjon Ubaydullayevich Ubaydullayev
Azizjon Ubaydullayevich Ubaydullayev
The brine of the Aral Sea is considered a complex source of lithium because it contains large amounts of magnesium, potassium, sulfate, and chloride, which prevent the direct preparation of Li2CO3. This work describes a technique based on selective precipitation and crystallization of impurities, followed by the isolation of high-purity Li2CO3. Initially, magnesium and potassium were precipitated together with Na2HPO4 as MgKPO4, and sulfate was precipitated as CaSO4·2H2O using CaCl2. Such pretreatment made it possible to remove up to 97.1%, 96.3% and 93.4% of magnesium, potassium and sulfate, respectively. Analysis by XRD and EDAX showed that the obtained precipitates consisted of gypsum and phosphate, which can be used as mineral or fertilizer by-products. Then the purified solution was treated with Na2CO3 in a stirred crystallizer at 50 °C. Focused Beam Reflectance Measurement (FBRM) analysis showed that increasing the stirring speed from 400 to 600 rpm resulted in smaller Li2CO3 particles. The influence of Na2CO3 feed rate was less, but the aggregation of crystals increased at higher concentrations of Na2CO3. The proposed technology made it possible to obtain 99.5% pure Li2CO3 (for the production of lithium-ion batteries). It was shown that the separation of impurities allows controlling the formation and growth of Li2CO3 from natural brine. The developed method provides the opportunity to prepare lithium carbonate suitable for batteries from Aral Sea brine with separation of useful by-products containing magnesium, potassium, calcium, phosphorus and sulfur.