An increasing number of electric vehicles, hybrids, and synergistic types are adding electronic components, driving up demand for lithium and its derivatives. These chemicals comprise 80% of the worldwide market and come in forms such as carbonate, lithium hydroxide and mineral concentrates. The use of lithium is predicted to surge by 60% in the coming years due to the proliferation of electric vehicles. This demands efficient and rapid deposit detection methods as well as economical and high-resolution exploration equipment. The quantity and geographical distribution of fossil and ore mineral deposits can be easily mapped using hyperspectral photography. Since salt lakes, oceans, and geothermal water hold the majority of the world’s lithium reserves ranging from 70% to 80%, these areas are ideal for the lithium extraction process. In this regard, there is an increase in research targeted at industrial lithium production from water resources. Recycling lithium-ion batteries is an alternative method that can be utilized to increase the production of lithium. Geothermal waters have lower lithium contents than brines and some of the processes are not suitable. Evaporation methods, solvent extraction, membrane technology, nanofiltration and adsorption can all be used to extract lithium from liquid media. Thus, lithium extraction from aqueous solutions was the focus of this review article, which aimed to provide straightforward technical solutions, low costs, decreased environmental impact and excellent selectivity for the lithium industry.
In this article, modern research on the visual-polythermal method was used to study the solubility level of the components in sodium carbonate - lithium chlorid In this article, modern research on the visual-polythermal method was used to study the solubility level of the components in sodium carbonate - lithium chlorid
The interaction of calcium dihydrogen phosphate with copper, zinc and cobalt sulfate salts in dilute solutions (0.01 M) at 303.15 and 353.15 K, depending on the Ca(H2PO4)2:MSO4 ratio, was studied. It is found that at a molar ratio of 1:1, the pH, electrical conductivity, viscosity and density have extreme values, which indicates a change in the composition of solutions. The results of chemical analysis at a ratio of of 1:1 showed the formation of calcium sulfate and hydrogen phosphates of copper, zinc and cobalt, regardless of temperature. This indicates that calcium dihydrogen phosphate undergoes hydrolysis in an aqueous medium and then an exchange reaction occurs between microelement sulfates and calcium hydrogen phosphate. The addition of phosphoric acid into mixing solutions prevents the hydrolysis of calcium dihydrogen phosphate and the reaction products were calcium sulfate and dihydrophosphates of copper, zinc and cobalt.
The growing global demand for lithium, driven by its key role in rechargeable batteries for electric cars and portable electronics, underscores the need to investigate sustainable sources and efficient processing techniques. This review critically reviews the existing literature on lithium’s characteristics, applications, global reserves, and extraction technologies. Although new geological surveys in 2023 added around 62 million tons to world lithium reserves, only a small portion may now be commercially extractable. Forecasts suggest lithium demand could reach 20 million metric tons by 2100, with annual growth rates ranging from 8 to 11%. Recycling spent lithium-ion batteries is projected to supply up to 25% of global lithium demand by 2050; however, complex waste chemistries and low lithium concentrations pose significant recovery challenges. In response, around fifteen new industrial projects targeting both hard rock and brine resources have been proposed, collectively offering an annual capacity of 320,000 tons of lithium carbonate equivalent. Additionally, emerging initiatives aim to extract lithium from oilfield brines. The world is experiencing tremendous growth in electric vehicle (EV) production, resulting in most lithium being extracted from water-based reservoirs such as brines, seawater, and geothermal waters. Among extraction methods, impurity precipitation and impurity adsorption emerged as the two most promising and cost-effective approaches for treating difficult solutions. In particular, impurity precipitation can effectively exclude interfering substances in saturated brine to produce a lithium-rich solution. Subsequent adsorption of these purified solutions then allows efficient, selective separation of lithium ions. Finally, combining these methods creates a feasible, sustainable, and eco-friendly system to meet future global lithium demand.
The solubility of components in the system potassium sulfate-lithium sulfate-water was studied using the visual-polythermal method in a wide range of temperatur The solubility of components in the system potassium sulfate-lithium sulfate-water was studied using the visual-polythermal method in a wide range of temperatur
The brine of the Aral Sea is considered a complex source of lithium because it contains large amounts of magnesium, potassium, sulfate, and chloride, which prevent the direct preparation of Li2CO3. This work describes a technique based on selective precipitation and crystallization of impurities, followed by the isolation of high-purity Li2CO3. Initially, magnesium and potassium were precipitated together with Na2HPO4 as MgKPO4, and sulfate was precipitated as CaSO4·2H2O using CaCl2. Such pretreatment made it possible to remove up to 97.1%, 96.3% and 93.4% of magnesium, potassium and sulfate, respectively. Analysis by XRD and EDAX showed that the obtained precipitates consisted of gypsum and phosphate, which can be used as mineral or fertilizer by-products. Then the purified solution was treated with Na2CO3 in a stirred crystallizer at 50 °C. Focused Beam Reflectance Measurement (FBRM) analysis showed that increasing the stirring speed from 400 to 600 rpm resulted in smaller Li2CO3 particles. The influence of Na2CO3 feed rate was less, but the aggregation of crystals increased at higher concentrations of Na2CO3. The proposed technology made it possible to obtain 99.5% pure Li2CO3 (for the production of lithium-ion batteries). It was shown that the separation of impurities allows controlling the formation and growth of Li2CO3 from natural brine. The developed method provides the opportunity to prepare lithium carbonate suitable for batteries from Aral Sea brine with separation of useful by-products containing magnesium, potassium, calcium, phosphorus and sulfur.