There are many redundant nodes and inflection points in the path planned by the traditional A* algorithm, leading to the inefficient trajectory planning of the automatic guided vehicle (AGV) in the multi-static obstacles environment. The artificial potential field (APF) algorithm suffers from the problem of unreachable objectives and falling into optimal local value. This article studies the trajectory optimization of AGVs to improve the trajectory planning algorithm’s iteration efficiency and shorten the trajectory’s total length. This article establishes the forward kinematic and unified robot description format model of the AGV and proposes the APF-A* algorithm for trajectory planning. The search cost and the number of turns are effectively optimized. The article simulates the APF-A* algorithm, the results are compared with the trajectory before optimization, and the optimized time is 60% less than that before optimization. The experimental platform of AGV trajectory planning is built, and the algorithm verification experiment of AGV trajectory planning is carried out. The experimental results show that the algorithm studied in this article achieves path smoothing and trajectory length optimization.
Aiming at stability and safety problems caused by the actuator failure of the automated guided vehicle under the condition of centroid position change. The four-wheel independent drive four-wheel independent steer (4WID/4WIS) AGV is studied for fault-tolerant control of single-wheel drive actuators under the centroid position variation condition. First, 3-DOF vehicle model, drive-wheel dynamics model, HSRI tire model, and the actuator loss of effectiveness model established. Second, a hierarchical controller is designed with an optimal input controller based on Model Predictive Control (MPC) theory of the upper layer, a desired yaw moment solver based on fuzzy theory of the middle layer, and a torque reconstruction controls distributor based on the control gain in the lower layer. Then, the AGV is simulated and analyzed in straight line and double line change conditions. The simulation results show that the yaw rate and the centroid sideslip angle can closely track the theoretical value. The difference between the theoretical value is kept within 5%. Finally, the 4WID/4WIS AGV prototype vehicle was developed and tested for straight-line and double-lane change condition. The difference between simulation and experiment was within 4%. The experimental results show that the designed controller is effective.
17 September 2022 in Mathematical Problems in Engineering
The centroid of the Automated Guided Vehicle (AGV) equipped with the load platform is high, and it is prone to rollover when driving sideways on a slope. To solve this problem, this study proposes an anti-rollover cooperative control strategy combining differential drive, active steering, and load platform. According to the characteristics of AGV, the dynamic coupling of each subsystem is analyzed. The expected yaw stability control torque is calculated based on optimal control. The active steering controller is designed based on the model predictive control. The expected roll control torque is solved by the proposed sliding mode variable structure control method to dynamically adjust the centroid. Evaluation of the overall control system is accomplished by simulations and experiments under different load conditions of the AGV in the lateral driving condition on a slope. Compared with the PI controller, the sideslip angle decreases by 14.62% and 18.24%, and the roll angle decreases by 12.38% and 14.93% under high and low load conditions, respectively. The error between the experimental and simulation results is within 7.8%. It shows that the proposed cooperative control strategy can improve the stability of AGV under different load conditions and reduce the rollover probability when the AGV is driving sideways on a slope. This research provides a theoretical and experimental basis for active safety control of AGVs.
In current intelligent manufacturing workshops, multi-automated guided vehicle (AGV) systems often face issues such as uneven task allocation, path conflicts, and idle travel, which significantly affect scheduling efficiency. To address these problems, this paper proposes an improved ant colony algorithm that collaboratively optimizes task allocation and path planning by integrating path costs and AGV task execution capabilities. The algorithm utilizes shortest-path planning results to optimize task allocation priorities, achieving synchronized optimization of task scheduling and path planning. Based on this, a multi-objective scheduling model is constructed with the goal of minimizing task completion time, idle travel distance, and total travel distance. The results show that the method effectively shortens task completion time and significantly improves scheduling efficiency, verifying its feasibility for application in intelligent manufacturing workshops.
Addressing the challenges of inefficient prolonged trajectory resolution and unreliable dynamic obstacle avoidance for intelligent vehicles in complex confined environments, this study proposes an innovative hybrid path planning method. Its core novelty is the deep integration of an enhanced A* algorithm for smooth global planning with a fuzzy logic-controlled Dynamic Window Approach (DWA). The enhanced A* generates efficient and smooth global paths, while fuzzy control significantly improves DWA’s robustness in dynamic, uncertain scenarios. This hybrid strategy achieves efficient synergy between global optimality and local reactive obstacle avoidance. Simulations demonstrate its superiority over conventional A* or DWA in path length, planning efficiency, and obstacle avoidance success rate. Experimental validation on a physical platform in simulated complex scenarios shows an average trajectory deviation ≤ 7.14%. The work provides an effective theoretical and methodological framework for navigation in constrained spaces, offering significant value for practical applications like logistics and automated parking.
Auxetic cellular materials attract increasing attention for crashworthiness and impact protection due to their negative Poisson’s ratio (NPR). However, conventional double-arrowhead auxetic honeycombs (DAHs) with straight ligaments often exhibit limited energy absorption and unstable collapse under large deformation. In this study, a curvilinear hybrid auxetic honeycomb (CHAH) is proposed by replacing straight walls with smoothly curved ligaments and embedding a circular positive Poisson’s ratio subcell to provide symmetric support. The mechanical behavior of the CHAH is investigated through a combined experimental–numerical approach. Finite element simulations are validated by quasi-static compression experiments, and a parametric study is conducted to evaluate the influence of key geometric variables on specific energy absorption (SEA) and peak crushing force (PCF). Based on the validated simulations, a multi-objective optimization framework integrating optimal Latin hypercube sampling, radial basis function surrogate modeling, and NSGA-II is employed to optimize the structural parameters. Compared with the conventional DAH under identical material and volume conditions, the CHAH exhibits significantly improved deformation stability and energy absorption capability, with SEA increasing by up to 67.06% and a more stable plateau response. In addition, SEA and PCF can be effectively tuned by varying the geometric angles (θ1, θ2).