Bram Noordman

Mr. Bram Noordman

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 January 2023 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
BNBram Noordman
Bram Noordman
YTYoeri Ton
Yoeri Ton
JTJort van Den Toorn
Jort van Den Toorn
MSMarc de Smit
Marc de Smit
RHRalph Haagsma
Ralph Haagsma
WBWouter van Den Brink
Wouter van Den Brink
Rotating shaft balances (RSBs) are devices that are used to measure rotor blade forces and moments of wind tunnel models during wind tunnel tests. The design of an RSB can be challenging, because it has to comply with many and sometimes contradicting requirements such as high stiffness and high strain gauge bridge outputs. The manufacturing of a conventional RSB consists of different subsequent steps, which can be time consuming, expensive and associated with many risks. Therefore, in this work, the authors investigate if a RSB can be designed by topology optimization and manufactured by 3D printing. A topology optimization method was developed with as design objective the minimization of strain energy with constraints for the volume of the RSB’s midsection, defined stresses at strain gauge locations used for the measurement of axial force and torque and an overhang constraint for additive manufacturing. The optimal preliminary design found by topology optimization was translated into a final printable design with the highest bridge sensitivity for axial force and torque, sufficient output for in-plane forces and moments and an acceptable safety factor on strength for combined loads. After adding extra supports required for printing, the RSB was successfully printed in metal by the laser powder bed fusion process, resulting in a product without external defects. The same topology optimization and manufacturing method can potentially be used for other balance types, leading to a reduction in total lead time and manufacturing costs while increasing the design freedom.

14 March 2025 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
JKJohan Kos
Johan Kos
MMMarie Moghadasi
Marie Moghadasi
TKTim Koenis
Tim Koenis
BNBram Noordman
Bram Noordman
OEOzan Erartsin
Ozan Erartsin
RNRuben Nahuis
Ruben Nahuis
Innovative structures technologies can contribute to increasing the sustainability of next-generation aircraft. Advanced multi-disciplinary physics models, combined with data-based models, are needed to obtain optimized structures with maximum contributions to sustainability throughout the life cycle. Such models are needed for next-generation aircraft products, for better production of their parts, and for representative testing of their innovative systems. Modeling challenges addressed recently will be presented and illustrated in their industrial context. In particular, fast in-line detection of defects in large composite aircraft parts during their high-rate production, induction welding of thermoplastic carbon-fiber reinforced parts, and accurate design of composite fan blades for wind tunnel testing of fuel-efficient Ultra-High Bypass Ratio (UHBR) turbofan engines will be presented.

19 May 2026 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
BNBram Noordman
Bram Noordman
AWAlbert de Wit
Albert de Wit
RCRalf Creemers
Ralf Creemers
ANArne te Nijenhuis
Arne te Nijenhuis
RURens Ubels
Rens Ubels
LLLeonardo Lecce
Leonardo Lecce
Hydrogen-propelled aircraft can enable net-zero CO2 emissions in aviation, which is the goal of the International Civil Aviation Organization (ICAO) for 2050. One drawback of onboard hydrogen storage in aircraft is the necessity for relatively large, pressurised storage volumes. To maximise H2 volumetric efficiency, the COmposite COnformal LIquid H2 Tank (COCOLIH2T) project attempts to design, build and test a vacuum-insulated liner-less cryogenic conformal thermoplastic composite tank with conditioning subsystems for safe operation. The tank must be compatible with the design envelope in the empennage, specifically towards the aft of the pressure bulkhead of an ATR 72-like aircraft. The tank design, analysis, optimisation and demonstrator manufacturing are presented in this paper.