A water-based AgNW ink for large-scale flexible transparent conductive films was developed via a systematic research procedure.

To improve the corrosion resistance and wear resistance of electroless nickel-phosphorus (Ni-P) coating on magnesium (Mg) alloy. Ni-P-Al2O3 coatings were produced on Mg alloy from a composite plating bath. The optimum Al2O3 concentration was determined by the properties of plating bath and coatings. Morphology growth evolution of Ni-P-Al2O3 composite coatings at different times was observed by using a scanning electronic microscope (SEM). The results show that nano-Al2O3 particles may slow down the replacement reaction of Mg and Ni2+ in the early stage of the deposition process, but it has almost no effect on the rate of Ni-P auto-catalytic reduction process. The anti-corrosion and micro-hardness tests of coatings reveal that the Ni-P-Al2O3 composite coatings exhibit better performance compared with Ni-P coating owing to more appropriate crystal plane spacing and grain size of Ni-P-Al2O3 coatings. Thermal shock test indicates that the Al2O3 particles have no effect on the adhesion of coatings. In addition, the service life of composite plating bath is 4.2 metal turnover, suggesting it has potential application in the field of magnesium alloy.

Hydrophilic cellulose nanocrystals (CNC) are typically poorly dispersed in non-polar polymer matrices and, hence, a method for the surface modification of CNC is developed for improving this dispersion. This method included an esterification reaction with acetic anhydride, butyric anhydride, and caproic anhydride. The particle size distribution (range of sizes: 80–310 nm) of CNC was determined. The SEM-EDAX indicated that (i) the structure of CNC was maintained even after incorporation of the acid anhydride and (ii) the carbon C content of modified-CNC was higher than that of pure CNC. The chemical structure of modified-CNC was identified via FT-IR and ¹³C NMR spectroscopy. The contact angle of CNC and modified-CNC with water and methylene iodide was measured. The surface energy of modified-CNC was lower than that of pure CNC. Thermal-property measurements indicated that the initial decomposition temperature (based on 5 wt%) of the modified-CNC was slightly higher than that of CNC. Poly(butylene succinate) (PBS) composites were obtained by mixing modified-CNC into a PBS matrix via simple melt blending of a double screw. The PBS/modified-CNC composites were investigated via DSC and XRD. Tensile testing indicated that the tensile modulus improved gradually with increasing modified-CNC content, whereas the elongation at fracture decreased.

This review focuses on grain growth behaviors and the underlying mechanisms of bulk electrodeposited nanocrystalline nickel and nickel-iron alloys. Effects of some important factors on grain growth are described. During thermal-induced grain growth process, grain boundary migration plays a key role. For similar thermal conditions, due to grain boundary mobility with solute drag, limited grain growth occurs in nanocrystalline alloys, as compared to pure metals. Nonetheless, in the case of stress-induced grain growth process, there are a variety of mechanisms in samples having various deformation histories. As an example the grain growth of nanocrystalline nickel and Ni-20%Fe alloy with nearly the same grain-size distribution and average grain size is compared in this paper. Thermal analysis indicates nanocrystalline nickel is much more prone to rapid grain growth than nanocrystalline Ni-20%Fe alloy. Nevertheless, grain growth of nanocrystalline Ni-20%Fe is found to be more pronounced than nanocrystalline nickel during rolling deformation.

With the promising potential application of Ag/graphene-based nanomaterials in medicine and engineering materials, the large-scale production has attracted great interest of researchers on the basis of green synthesis. In this study, water-soluble silver/graphene oxide (Ag/GO) nanomaterials were synthesized under ultrasound-assisted conditions. The structural characteristics of Ag/GO were confirmed by Fourier transform infrared spectroscopy, X-ray diffraction, transmission electron microscopy, scanning electron microscopy and energy dispersion spectroscopy, respectively. The results showed the silver particles (AgNPs) obtained by reduction were attached to the surface of GO, and there was a strong interaction between AgNPs and GO. The antibacterial activity was primarily evaluated by the plate method and hole punching method. Antibacterial tests indicated that Ag/GO could inhibit the growth of Gram-negative and Gram-positive bacteria, special for the Staphylococcus aureus .