The soft robot manipulator is attracting attention in the surgical fields with its intrinsic softness, lightness in its weight, and safety toward the human organ. However, it cannot be used widely because of its difficulty of control. To control a soft robot manipulator accurately, shape sensing is essential. This paper presents a method of estimating the shape of a soft robot manipulator by using a skin-type stretchable sensor composed of a multiwalled carbon nanotube (MWCNT) and silicone (p7670). The sensor can be easily fabricated and applied by simply attaching it to the surface of the soft manipulator. In its fabrication, MWCNT is sprayed on a teflon sheet, and liquid-state silicone is poured on it. After curing, we turn it over and cover it with another silicone layer. The sensor is fabricated with a sandwich structure to decrease the hysteresis of the sensor. After calibration and determining the relationship between the resistance of the sensor and the strain, three sensors are attached at 120° intervals. Using the obtained data, the curvature of the manipulator is calculated, and the entire shape is reconstructed. To validate its accuracy, the estimated shape is compared with the camera data. We experiment with three, six, and nine sensors attached, and the result of the error of shape estimation is compared. As a result, the minimum tip position error is approximately 8.9 mm, which corresponded to 4.45% of the total length of the manipulator when using nine sensors.
10 October 2022 in IEEE Robotics and Automation Letters
Shape memory alloy actuators (SMA) are widely used in robots owing to their flexibility and light weight. However, there is a drawback in that SMAs need to be used as a bundle owing to their lower force density than the motor. In addition, SMAs require continuous current to maintain a contracted state, which results in the overheating of the actuator, causing breakdown and excessive energy consumption. This study presents a new locking system that can mechanically hold the contracted state of an actuator without consuming energy to overcome the disadvantages of a spring-type SMA. The locking mechanism was designed with a ratchet structure and pawl to prevent the actuator from stretching in the opposite direction when locked. In addition, to switch the locking and unlocking states with a single one-way actuation, a bistable retractable mechanism was applied to the system. Repeatability experiments and an analysis of the locking system resolution were conducted to validate the performance of the proposed mechanism. Furthermore, an underactuated finger applied to the proposed locking system was fabricated, and its feasibility is experimentally presented.
4 December 2024 in IEEE Robotics and Automation Letters
With the growth of logistics automation, there is an increasing demand for advanced grippers. This study presents a gripper that integrates suction cups into the fingertips to overcome the limitations of traditional robotic gripping methods. Designed with a 5-degree-of-freedom structure, the gripper allows for angle adjustment of the suction cups, facilitating effective grasping in various environments. Its adaptive grasping mechanism simplifies control by using the fingertips and distal phalanxes to cage objects without manually controlling them. The versatility of the gripper was tested by performing hybrid finger-suction gripping, as well as conventional finger and suction gripping. These advanced gripping strategies are designed to enhance flexibility and efficiency in logistics automation when handling a diverse range of objects.
9 December 2022 in Journal of Mechanisms and Robotics
This paper proposes a shape-adaptive electroadhesion dielectric elastomer actuator (EA-DEA) pad gripper that can actively adapt to the shape of curved objects and quickly handle various objects by combining an EA pad and a multi-layered DEA driven by electrostatic force. This gripper has a rapid release function capable of detaching thin and light objects in less than 0.2 s with bending motion of multi-layered DEA and reverse polarity voltage. Moreover, combined with a transform mechanism that changes the posture of the EA-DEA pad gripper, a multifunctional gripper handling various objects from thin to irregularly shaped objects is implemented. The high voltage controller is configured to generate the variable and reversible voltages required for the control of the developed gripper. To verify the performance and practicality of the proposed multifunctional gripper system, we demonstrate the gripping task in three modes formed by controlling the EA-DEA pad gripper and the transform mechanism to adapt to the object shape. According to the experimental results, this gripper can reliably and rapidly pick and place various objects, such as thin film, hexahedron, cylinders, spheres, irregular shaped, deformable, and fragile objects corresponding to each mode.
Increasing the force generation and scalability of soft pneumatic actuators poses significant challenges in robotics applications, especially where high load capacities and precise control are required. This paper presents UniBPAM, a novel, scalable soft pneumatic actuator optimized through 3D printing to enhance force generation. By analyzing design parameters, such as the number of sides, height, and origami factor, UniBPAM achieved a 21.48% increase in force generation. Scalable across diameters from 36 to 144 mm, the actuator demonstrated the ability to lift up to 57 kg with 84.9% strain at larger scales. Additionally, the BiBPAM variant enables bidirectional actuation in robotic joints via motion control, which is realized through PID systems, making it suitable for various robotic applications.
Soft pneumatic robotic joints driven by low-cost on/off solenoid valves are attractive for lightweight and compliant robotic systems, but precise control remains challenging because continuous actuation commands must be realized through discrete valve states subject to minimum pulse-width constraints. This paper presents a model-based constrained equivalent-control PWM (C-EC) framework for a dual-chamber bellows actuator driven by four on/off valves. An ideal duty ratio is derived so that the averaged differential pressure rate matches the desired value required to impose first-order inner-loop error dynamics. To make this law physically implementable, the ideal duty is projected onto the feasible duty set determined by the minimum reliable pulse width of the valves. The resulting duty projection error is explicitly incorporated into a Lyapunov-based analysis, yielding a uniform ultimate boundedness result for the closed-loop system under the proposed implementation and an analytical comparison with conventional discrete sliding-mode control (D-SMC). The valve flow model is parameterized through PWM step-test-based sonic conductance identification. The proposed framework is implemented on a custom 1-DOF rotary joint based on an aluminum-film spiral-duct bellows actuator. Experiments show that C-EC does not uniformly dominate D-SMC over all operating conditions, but it improves and in the medium-to-large positive-step regime and in long-hold regulation. In the representative 45°–65°–45° step-hold test, C-EC reduced the RMS tracking error by 39.3% and the differential pressure ripple by 34.5% relative to D-SMC. In the 65° long-hold test, the RMS tracking error and pressure ripple were further reduced by 35.4% and 37.9%, respectively. A loop-period comparison also showed that a 10 ms control period reduced duty projection and pressure ripple relative to 5 ms without degrading tracking accuracy.